2077288-1-S-Whirlpool-71001680-Bake Element - 240V
2077288-1-S-Whirlpool-71001680-Bake Element - 240V 2077288-2-S-Whirlpool-71001680-Bake Element - 240V http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/51255.gif

Bake Element - 240V

PartSelect Number PS2077288

The element has male terminals. This bake element is found on the bottom of the oven.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Compare At

    $51.65
  • You Save

    $8.61
  • Your Price

    $43.04
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 25 reviews What's this?
1-5 of 25
 

41 of 45 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCatherine from Allenton, MI

Replacing bake element as oven wouldn't heat

After viewing the diagram on partselect.com, I knew this would be easy. I first shut off the circuit breaker to the oven, then used a phillips screwdriver to remove the two screws on the plate securing the element. Once removed, I disconnected the two wires, and removed the old element. I then connected the two wires to the new element, and screwed the plate back into place. I then switched the circuit breaker back on and tested the new bake element which was working perfectly. This do it yourself repair saved me time and money not having to call and schedule a repair man. Thank you so much partselect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 15 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerCARROLL from ST. FRANCISVILLE, LA

No display & oven wouldn't heat

First I removed the two screws that hold the bake element. I then pulled it out far enough to disconnect the two wires, and reversed the process to connect and secure the new element. I then removed the screws located under the control panel that held it in place. I removed the wiring, 3 cable connections, from the clock circuit board, and the two screws holding it in place. I installed the new circuit board, and reconnected the wiring, and returned the control panel to its place. The wife was upset that she had offered to do some of my chores while I fixed the oven when she found that it had only taken me 10 minutes to make the repairs. The parts were a perfect match, and the job couldn't have gone any smoother.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerCrystal from Erie, PA

Lower oven element burned out

Stove is over 16 years old. I am getting new kitchen in the summer, did not want to buy another stove! I looked on line and found how easy it was to replace element. We turned off power as suggested and removed element to make sure it matched the one on line. I ordered element on Sunday afternoon and it arrived Tuesday afternoon, FedEx ground. Insert the clips and a couple screws and we were having oven fries for dinner. I could not be happier and pretty darn proud of myself for saving a couple hundred dollars on a repair man!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Bake Element - 240V

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWayne from Seward, AK

Oven would not heat to set temp

I rremoved two screws and pulled element out about 3 inches. I un hooked the two wires and tested with an ohnm meter to determine the condition of the element. Element was bad so I ordered a new one. Service and price were great. Easy fix. Thank you.
Don't forget to unplug first.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerRoy from Rocklin, CA

Bake element wore out. Replaced bake element.

Very easy. 1. Turn off power to oven. 2 move the adjustable grills out to gain better access. 3. There are two phillips head screws that hold a bracket to the back of the inside oven. Unscrew both screws. 4 pull the bake element out about 6". This exposes the two electrical connections. 5. Use a plier and wiggle the slide on connector off of the old bake element. 6. With your fingers, slip the old connectors onto the new bake element. 7. Slide the element and wires back in the insulated pocket. 8. Screw both screws back in. 9. Turn on power and make your wife back you chocolate chip cookies just to "test". Sit in an easy chair and enjoy your cookies. If this took longer than 30 minutes inclding baking the cookies, it took you too long. If the cookies are not good, replace the wife. May take a little loger though :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 25