2077218-1-M-Whirlpool-71001564-Fan-Switch.jpg
2077218-1-S-Whirlpool-71001564-Fan-Switch.jpg 2077218-2-S-Whirlpool-71001564-Fan-Switch.jpg 2077218-3-S-Whirlpool-71001564-Fan-Switch.jpg

Fan Switch

PartSelect Number PS2077218

At a voltage of 125, this fan switch will allow for 6 amps, and at 250 volts, it will allow for 3 amps. Regardless of the voltage used, this switch still operates at 1/4 horsepower.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 12 reviews What's this?
1-12 of 12
 

18 of 23 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerLonnie from Markham TX

Replace high/low exhaust vent fan switch

Loosen 2 phillip screws that secure the Jeen Air cooktop vent fan switch and remove the 2-11/32" hex head nuts that secure the fan switch. Disconnect /reconnect the 3 wires to fan switch. Replace the switch cooktop console and retighten the 2 phillip screws. Cleanup.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJon from Anaheim CA

Fan switch out , burner switch out too

shut off power , remove vent cover, 2 screws to free the switch box , there was enough slack to turn it over , idendtify switches to be replaced , double check you got the right ones , got em , nut driver for the fan switch, torex for the burner switch , test ,put it back together , and clean up , no more than a half hour . order parts on monday , delivered on tuesday afternoon with 3-5 day shipping. thanks guys

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerThomas from Moneta VA

Fan switch and indicator lights disintegrated

Turned off the power. Removed the assembly with two screws then removed the switch with two screws. Pulled off the wires. Put on the new switch and lights and reconnected the wires. Reattached the assembly. Turned on the power. All OK.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerMichael from Bozeman MT

Wings which hold switch broke off.

Turn off power, removed wires from switch, unscrewd lock nuts. Did the reverse to put the new switch with the exception of the the power which should always be turned off first. Took less than 5 min. to install. Wife happy!! which makes me happy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerBarry from Quincy FL

Fan stopped working - switch fell apart

Two screws inside the exhaust box to take out the switch assembly and 2 nuts on the switch. Nothing to it

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJames from Hazel Green AL

Bad fan switch

Remove switch cover with two screws ,remove two nuts holding switch in place ,remove switch,then reverse procedure with new switch.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerLois from Alpharetta GA

Fan switch pushed through, plastic housing broken

Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerDarrell from Moultrie GA

Switch too big for hole

switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerDavid from Boone IA

Replace fan switch

remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerGregory from Hickman KY

Fan stopped working.

First I removed the two screws that hold the switch in place. I then pulled the switch out about 3 inches and disconnected the three wires from the old switch and replaced the new switch....

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKatrina from Coos Bay OR

Fan on built in jenn-air went out.

ordered part, called friend who does odd jobs, and he came and turned off electric, unscrewed the area, pulled out old plug, plugged in the new. Turned on electric and walla, fan works !!!! thank you very much. Part arrived in very short length of time. I was surprised.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Fan Switch

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

Customerjohn from Ironton OH

Defetive fan switch

throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-12 of 12