| |
14 of 17 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerLonnie from Markham TX
Replace high/low exhaust vent fan switch
Loosen 2 phillip screws that secure the Jeen Air cooktop vent fan switch and remove the 2-11/32" hex head nuts that secure the fan switch. Disconnect /reconnect the 3 wires to fan switch. Replace the switch cooktop console and retighten the 2 phillip screws. Cleanup.
|
8 of 10 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerJon from Anaheim CA
Fan switch out , burner switch out too
shut off power , remove vent cover, 2 screws to free the switch box , there was enough slack to turn it over , idendtify switches to be replaced , double check you got the right ones , got em , nut driver for the fan switch, torex for the burner switch , test ,put it back together , and clean up , no more than a half hour . order parts on monday , delivered on tuesday afternoon with 3-5 day shipping. thanks guys
|
4 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
CustomerThomas from Moneta VA
Fan switch and indicator lights disintegrated
Turned off the power. Removed the assembly with two screws then removed the switch with two screws. Pulled off the wires. Put on the new switch and lights and reconnected the wires. Reattached the assembly. Turned on the power. All OK.
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers
CustomerBarry from Quincy FL
Fan stopped working - switch fell apart
Two screws inside the exhaust box to take out the switch assembly and 2 nuts on the switch. Nothing to it
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Screw drivers
CustomerMichael from Bozeman MT
Wings which hold switch broke off.
Turn off power, removed wires from switch, unscrewd lock nuts. Did the reverse to put the new switch with the exception of the the power which should always be turned off first. Took less than 5 min. to install. Wife happy!! which makes me happy.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerJames from Hazel Green AL
Bad fan switch
Remove switch cover with two screws ,remove two nuts holding switch in place ,remove switch,then reverse procedure with new switch.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerLois from Alpharetta GA
Fan switch pushed through, plastic housing broken
Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsNutdriver
CustomerDarrell from Moultrie GA
Switch too big for hole
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerDavid from Boone IA
Replace fan switch
remove two nuts and install new switch, then change wire connections from the old switch to the new one.
Then place it back together.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerGregory from Hickman KY
Fan stopped working.
First I removed the two screws that hold the switch in place. I then pulled the switch out about 3 inches and disconnected the three wires from the old switch and replaced the new switch....
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKatrina from Coos Bay OR
Fan on built in jenn-air went out.
ordered part, called friend who does odd jobs, and he came and turned off electric, unscrewed the area, pulled out old plug, plugged in the new. Turned on electric and walla, fan works !!!! thank you very much. Part arrived in very short length of time. I was surprised.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsNutdriver
Customerjohn from Ironton OH
Defetive fan switch
throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on
|