| |
4 of 8 people found this instruction helpful
Parts Used
-
- Crisper Drawer Shelf Support
- SCREW
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMichael from Torrance CA
Lower left shelf support was broken
I removed all contents from the lower shelf. I, then removed both of the pull out drawers. Secondly, I removed the lower glass shelf and the glass support tray. At this point all four plastic shelf supports were accessible. I removed the inner screw from all four supports and replaced with four new shelf supports. Then reassembled in reverse order. Very easy to do!
|
2 of 2 people found this instruction helpful
Parts Used
-
- Crisper Drawer Shelf Support
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customervickie from Acworth GA
Broken shelf supports
It was easy breezy!! I felt like an empowered woman that I did it myself. I simply removed the old shelf supports with a screwdrive and inserted a screw thru the new supports and screwed them in.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Screw drivers
CustomerMark from Wyoming RI
Freezer cold/reefer hot
Took out all shelves and racks. Pulled out plastic cover. Removed screws holding control unit. Removed unit and accresses defrost circuit board. Replacement is in a cover. One screw would not engage so did not put it back in. Reefer was cold within hour of start and is now 1 week after. Unit would start out cold and then warm up before replacement.
Other parts were snap in furnishings that had become damaged with use.
|
1 of 1 people found this instruction helpful
Parts Used
-
- Crisper Drawer Shelf Support
Level of DifficultyA Bit Difficult
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDeanie from Amarillo TX
The support had broken and the shelf was just hanging there.
I unscrewed the support and replaced it with one that I ordered. It was fast and easy.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Crisper Drawer Shelf Support
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerTom from Bethlehem PA
Shelf supports broke
Took out lower shelf. Unscrewed screws holding two broken shelf supports and removed broken supports. Replaced with new supports and screwed in the screws. Nothing to it.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Crisper Drawer Shelf Support
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerEdward from Tullahoma TN
Shelf support btoken.
Removed screw holding the broken support then using the same screw installed new support. Easy job.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Crisper Drawer Shelf Support
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerLucien from Cambridge MA
Identifying the part on the parts diagram took the longest. Finding the screw driver bit that would remove the old screw that held the original shelf support took longer than the actual repair.
Once I identified the bit that would remove the screw, the rest of the repair took 5 minutes. I removed the screw and discarded the remains of the original but now broken shelf support. With the same screw I simply attached the new shelf support that I received from PartSelect.com. End of story.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJaynab from Norwalk CT
Replace glass shelf and support
The items arrived the next day, in perfect condition (I was concerned about the tempered glass shelf in the mail). These items saved me from buying a new refrigerator!
|
0 of 2 people found this instruction helpful
Parts Used
-
- Crisper Drawer Shelf Support
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerJoe from West Henrietta NY
Supports inside of refrig. Broke, two on right side.
Removed the Crisper drawers and shelf. I then used a nutdriver to remove the broken supports, and installed the new supports using the same screws.
|
3 of 19 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsPliers, Screw drivers
CustomerJames from Bryan TX
Oven wouldn't heat.
The repair was a simple exercise in throwing the fuse, removing 2 screws, and a 1 for 1 replacement of the connections for wiring. We turned on the power, and Viola it was an oven, and not a digital boat anchor.
|