Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2062891
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
This fan blade attaches to the evaporator fan motor which is located in the back of the freezer.
If the fan blade needs replacement you will hear a loud noise coming from the refrigerator while the refrigerator cycles on. It will go away when it cycles off. (Note: in many cases you only need to replace the fan blade and retaining clip. Purchase both parts together. I thought I could use my old clip just to find out that the fan blade design changed and the old retaining clip would not work.)NOTE: My refrigerator has an ice maker. delete the steps for the ice maker if you do not have one. - I call the evaporator cover the back panel.- I call the tunnel assembly the fan cover. 1) Empty contents of freezer - Only freezer. (Note: leave refrigerator section alone) Remove wire rack by lifting and pushing in one side to free the other side. It may be a bit of a struggle but the holes that the wire rack sit in are recessed in the middle to allow removal. (Look at other wire rack holes to see where the holes exist.)2) Set dial in refrigerator to "OFF" then unplug refrigerator (safety first)3) Remove one screw below the ice maker holding the ice maker to the side of the cabinet. 4)Push up on ice maker - Slide Ice maker up and dismount from mounting bolts. 5) Once the ice maker is dismounted you will expose the ice maker wiring harness - Unplug ice maker harness from rear panel. 6) Remove ice maker. 7) Remove ice maker mounting bolt closest to rear of refrigerator to facilitate removal of back panel.8) Remove 4 screws on back panel and slide panel toward you. 9) Un-clip wiring harness attached to back panel that serves the ice maker (this protrudes from the back panel.) and push it through the back panel - 10) Lay panel down and unclip fan housing (Tunnel Assembly) from back of panel (Evaporator Cover) (note other instructions will tell you to remove this before the back panel. I found it easier this way. (Note the fan is attached to the back panel (Evaporator Cover). 11) After the fan cover is un-clip it hinges from the top. Lift panel - unhinge fan cover and expose fan. 12) The fan has a clip on the end that looks like a compressed wire spring. Pry off with a flat tip screw driver.13) Pull fan blades towards you and remove from motor shaft. 14) Inspect shaft and wipe it off. 15) Press new fan blade assembly on shaft with you fingers. you will be able to see the shaft from the front of the fan blade as the fan blades have a split in hub area. Seat the fan blade on the shaft as far as it will go. 16) Install new fan blade clip (I used a flat screw driver and pushed it on the fan blade by working different sides of the spring (be careful). 17) Reassemble in reverse order. I hope this helps. The job is reasonably easy for the novice and will save on a repairman coming out to install a fan blade and clip which is really a 15 minute job for the professional.
Help other customers find the most helpful instructions.
Were these instructions helpful?
The center hub of fan blade had cracked and had slipped off of fan motor shaft. I replaced fan and motor by pulling the shelf from freezer, removing 4 screws holding freezer back panel, tipped panel out and removed/replaced fan. Reassembled and it worked fine.
Removed freezer shelf. Shelf did not move to one side easily for removal. Removed fan cover (snaps in place), pulled off old fan and slid new fan blade onto shaft and installed clip.
Found evaporator fan blade not attached to motor, it's hub was cracked. My wife wanted to buy a new fridge and I fixed it for $7 in parts. Removed freezer shelf, unscrewed and removed back panel, uncliped fan cover from back panel, replaced blade and reassembled.
I removed the fan cover and pulled out the fan that had the broken piece and replaced it with the new parts. Very easily done. This simple procedure would have cost over 75 to 100 dollars. I did it with less than 50
The first step was to get the wire rack out of the freezer, which seemed to be permanent until I completely dismantled it with the nippers. Then I used a Phillips head screwdriver to take out the ice maker. Now the back of the fridge is clear to be opened. Just push down on the top of the round part while squeezing in at the sides and pull toward yourself. There is the fan (which was not connected in my case hence the rattling). Push new fan into place and connect pin... Total time 30 minutes to one hour. Except that it took two months for the fan to come in on back order... And the fan has a clip on it, so the extra clip was completely useless.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.