2061545-1-S-Whirlpool-61623-Thermostat  Boosting  Heater
2061545-1-S-Whirlpool-61623-Thermostat  Boosting  Heater 2061545-2-S-Whirlpool-61623-Thermostat  Boosting  Heater 2061545-3-S-Whirlpool-61623-Thermostat  Boosting  Heater

Thermostat Boosting Heater

PartSelect Number PS2061545

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Takes too long to dry.
  • Compare At

    $23.42
  • You Save

    $3.90
  • Your Price

    $19.52
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 5 reviews What's this?
1-5 of 5
 

13 of 20 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerDeanne from Visalia CA

Taking to much time to dry

took off lower front panel was able to reach all parts ...all parts i ordered were perfect matches........

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Socket set

CustomerDonald from Madison WI

Dryer shut down before clothes were dry

... I figured it was some over temp switch but then read about the gas solenoid problems others were having... bought $100.00 worth of parts... saved the old just in case down the road I might need them... figured a service call would cost me that much... now lots of new parts... and a working dryer. Done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerThomas from Norristown PA

Gas dryer, would only work when it felt like it.

Make a long story short, dryer was on fire from lint in the bottom of it. burned up some wires & other parts. it was easy to repair the wire & replace the parts every thing worked out fine. REMEMBER TO CLEAN OUT THE LINT IN THE BOTTOM OF THR DRYER not only the lint filter or this could happen to you.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Socket set, Wrench set

CustomerWalter from Cairo GA

Initially taking 3 cycles to dry completely, then no power at all.

In my case I had no idea initially what was wrong so I tore the entire dryer apart. Took the control panel apart, the front kick plate off, the door assemly off, then took the entire dryer housing off the base so I could get to everything. It was at this point I decided to try to seriously repair it myself. I found PartsSelect, read through the appropriate repair stories and determined the only real possible parts. I ordered the parts, received them promptly, and replaced 4 of the 5. The parts were easy to replace, just unplug the wires, used a socket set to remove the bolts holding them and replaced. I also unplugged the two wires to the element, unbolted it, cleaned it out and replaced it. The 5th part, the roller shaft did not have to be replaced. The original was in fine condition, it had simply loosened and was wobbly from 12 years of use. The bearing was still perfect with no slack in the shaft at all. After hooking up what I needed to for a test run, all was well. I then took about 2 hours to put everything back together. The dryer now works perfectly........dries loads completely in approx. 30 minutes and runs whisper quiet.

Help other customers find the most helpful instructions.

Were these instructions helpful?

41 of 1292 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set, Wrench set

Customerrussell from anamosa IA

Would run but would not heat

removed front cover and top took drum out remove heating unit replced limit switch and fuse reinstalled installed new idler put new belt around drum installed drum replaced glides put top back on and front cover . then replaced boosting heater witch is on the blower also cycling thermostat

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5