| |
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:1- 2 hours
Tools
CustomerLarry from Sun City AZ
Ice cubes jam in the ice dispenser shute
Remove (slide forward) the ice dispenser drain pad from the bottom of the ice dispenser assembly on front of the freezer door. Removing two screws (star head) at the bottom allows the ice dispenser cover to be removed. Remove 3 screws holding the ice dispenser assembly to the freezer door to gain access to the flapper. Remove and replace the flapper and reverse the steps to reassmble.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsScrew drivers
CustomerPeter from Matamoras PA
Water was going all over when someone tried to fill glass
Removed two star screws on plate, then two chute screws which allowed me to remove the chute. Then I removed the two screws which held the assembly in place, we had to pullout the assembly about three inches. (I had my wife hold that out of the way) Then I reached in behind the assembly and removed the chute door. At that point I saw that the tab which hold it in the opening mechanism was broken off. So I reassembled everything without the chute door and put a dishcloth in the chute to keep the cold in and the heat out. (during this time we had to manually take ice out of the hopper) I then went on line to partselect.com and ordered the part. It came in 3 days and my wife and I opened it all up again, snapped the chute door in place, removed the dishcloth, put the assembly and plate back together and it works like new.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJacqueline from Grimes IA
Ice door broke
Removed 5 screws, took unit apart, replaced part, put back together. Just be sure to have the solenoid connected to the ice door lever the right way before you reassemble.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJames from South Portland ME
The ice door no longer worked
I removed the screws that held the control panel in place. Unplugged the wiring cable and put the control panel aside. I removed the old broken part and inserted the new part. Very easy. Put everything back together and it worked like new.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRobert from Washinton MO
Part broke for the 2nd time since we got the refrigerator
took off the covers and put in the new part and then put it back together.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerGregory from Copiague NY
Ice door broke.
I removed the ice door panel. I use a torque driver to remove the 3 screws holding it on. Quick change of the broken door flap and reassemble the unit. Very quick and easy job. Just be sure to replace the activation piston that opens the door back properly. Good luck with you repair.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJames from Johnstown CO
Ice door broken
Removed overfill tray by sliding out away from door, 2 screws underneath need to be removed and front of tray cover can be slid up and removed unplug 1 small cable if you want to set aside. 4 screws need to be removed to pull complete ice tray door assy. away from fridge door. Ice door can then be remove and new one slipped into solenoid jaws that hold it closed until activation.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerSamuel from Burke VA
Ice chute door return spring
Used your instructions . went very well about 10 min.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerStuart from Oviedo FL
Broken ice chute door
Easy repair. Removed 5 screws, disconnected the curcuit board and slipped in the new door. Hardest part was fiddling it all back together after reconnecting the curcuit board. The cable is a little too short.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRALPH from WHEELING WV
Flap on ice door
taking apart and putting new one on is very very easy but the magnet pin that open and shuts had to work with for a while i have big hands and small space but once put it together very easy assembly.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
Tools
CustomerRandy from Taylor AL
Ice door broken tab - won't close completely
Parts arrived within a couple of days. Repair was easy using a torx driver. I removed the screws that held the cover onto the door and then a couple more once the cover was removed. Ice door snapped into place and reassembly was a simple reversal of the disassembly. Unit now works great. Parts were very reasonably priced and delivery was very timely.
|
19 of 644 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerEdward K. from Meansville GA
Door broke on ice maker
removed 4 screws and removed the unit from the DOor. replace the broken part. Then relace unit back into the door. Iwas very please how quick I received the part.
|