2061138-1-S-Whirlpool-61005883-Ice Chute Door
2061138-1-S-Whirlpool-61005883-Ice Chute Door 2061138-2-S-Whirlpool-61005883-Ice Chute Door http://www.partselect.com/Schematics/Maytag/54555.gif

Ice Chute Door

PartSelect Number PS2061138

This ice door is used to seal off the ice chute when not in use.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker won’t dispense ice.
  • Door won’t open or close.
  • Leaking.
  • Not dispensing water.
  • Door Sweating.
  • Compare At

    $15.80
  • You Save

    $2.63
  • Your Price

    $13.17
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Ice Door Strike

Part Number 2061141

This door strike is located within the mechanical components if the ice and water dispenser. With the help of the solenoid, this piece opens and closes the ice dispenser door.

$4.21
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 42 reviews What's this?
 

8 of 9 people found this instruction helpful

Parts Used:
  • Ice Chute Door
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: John from Crothersville, IN

Ice chute flap broke

removed the ice chute door, unhooked the computer board replaced the flap. The only problem was the spring loaded part of the ice chute door come up and the little plunger came loose. It only took a few minutes to replace the plunger back in the holder and replaced the ice chute door. The best part of the whole job was that I ordered the part on Monday afternoon and the part was at my door Wednesday. The Parts did an excellent job of getting the part to me quickly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used:
  • Ice Chute Door
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Michael from Leesburg, FL

Ice jammed, water sprayed wrong place

Discovered ice door tab was broken. Ice door out of position.
Disassembled door dispenser, pretty easy, two torx screws on bottom, two on upper part of unit. Slid unit up slightly, it sets over two studs on the top. Unplugged wire connector, set aside unit. Looked on internet for a replacement part. These folks had the easiest to use web site. Found the part, ordered the part, received it next day, but only ordered the least expensive delivery method, since we are both in Florida it worked out well.
I did not know when I ordered this part I would get it this quickly. Because cold air was pouring out of the hole left by the removal of the ice door, I put wide painters tape over the hole on the inside of the freezer door. This greatly reduced the flow of cold air.
After I received the part, I clipped it in place and reassembled the unit, it did not work. The solenoid that moves the door just hummed like it was jammed. I took it back apart and realized that I did not get the bracket that moves the ice door reattached properly. After I made sure the bracket was properly attached, i reassembled the unit and it worked great. It actually took longer to type this description than it did to do the job.
Good Luck, Mike

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used:
  • Ice Chute Door
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Neale from Murrieta, CA

Ice delivery door would not close or open

Removed the door assembly with 4 Torx screws, replaced the broken door with the new one. The assembly is spring closed, so had to be pivoted into place. Then the door didn't open when the ice button was pushed, but made a loud snapping noise. After removal again, it was determined that the solenoid was not attached properly to the arm. After this was done and the whole assembly was put back on the door, everything worked fine.

Watch out for the circuit board at the front of the assembly, it carries a pretty good bite!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used:
  • Ice Chute Door
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Ralph from Wheeling, WY

Flap door broken

disassemble the front panel removed two screws and panel fell forward took old part out cliped in new one and reassembled very easy job

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Ice Chute Door
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: James from League city, TX

Ice door assembly tab broken

Just as described by others that have left feedback, I removed a total of 4 hex-screws to access the door. Removed the old one and replaced the door. I resecured the front panel and it was done.
Thanks again for the great experience.

Help other customers find the most helpful instructions.

Were these instructions helpful?