2060964-1-S-Whirlpool-61005619-Ice Enclosure
2060964-1-S-Whirlpool-61005619-Ice Enclosure 2060964-2-S-Whirlpool-61005619-Ice Enclosure 2060964-3-S-Whirlpool-61005619-Ice Enclosure http://www.partselect.com/Schematics/Maytag/51835.gif

Ice Enclosure

PartSelect Number PS2060964

This is the part that holds the ice bin and houses the auger motor which is sold separately.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker won’t dispense ice.
  • Ice maker not making ice.
  • Compare At

    $91.55
  • You Save

    $15.26
  • Your Price

    $76.29
In Stock
Order within the next 23 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 23 reviews What's this?
 

4 of 4 people found this instruction helpful

Parts Used:
  • Ice Enclosure
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Tom from Stockton, CA

Motor mounts broken loose from enclosure

Removed frozen foods and ice container to get to enclosure. Removed single screw with 1/4" nut driver. Disconnected wiring harness from behind housing after lifting up and out a bit. Removed components from back of old housing, reinstalled in new. Tapped prong loose from motor shaft to pull in though piece of old broken housing.(reverse threaded) Screwed back into place and replaced motor in proper location. Reinserted housing, replugged wiring harness, replaced 1/4" screw to secure. Placed ice tray back in line with prong and frozen food (still frozen)back in shelves. Quick, easy and auto ice in the door again! And for less than 80 bucks. Is this a great country or what?

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used:
  • Ice Enclosure
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers, Wrench set
Customer: Neil from Webster, MA

Back of the ice enclosure was broken so motor drive for ice despincer was pushed in

First I removed the 1 screw holding the Ice Enclosure in place. The enclosure would then pull out. However the wire in back was plugged in and you could not see how the female plug was locked to the male plug. By squeezing the top and bottom edges of the plug you will release the lock and plug will release with a pull.
Then I removed the unit from fridge.
after removing the 8 screws holding the motor and other fixture, I tried to install in replacement enclosure.
unfortunately, the u-drive that is attached to the gear box shaft and is used to turn the Ice despincer worm, was on so tight I could not remove it. (tried everything)
I then took a Dremal tool with disc cutter and where the shaft hole is I cut a rectangular hole large enough for the u-drive to fit through. Be careful not to cut the plastic braces behind the panel.
The motor and gear box then fits in the slots and you can screw in place.
Note: the green ground wire and red wire are tape together. the ground wire to gorund a red wire to closest terminal. White wire to terminal on bottom.
Slid unit part way back in freezer, reach in back and connect plug. (only connects one way)
Then slide rest of the way in, insert screw to hold in place. Good Luck, mine works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Paul from kansas city, MO

Ice enclosure cracked

Remove ice maker. Remove single screw from under enclosure. Unplug wiring harness from refrigerator. Remove Ice enclosure. Removed metal yoke (left hand thread) with light tap from rubber hammer then removed all screws holding motor assembly and yoke assembly. Reverse the procedure to install components. Plug in wiring harness and install enclosure. Align ice dispenser with metal yoke on enclosure and install ice dispenser.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Ice Enclosure
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver
Customer: Maureen Murray from Rochester, WA

The drive motor for ice cubes, and solenoid had broken off from the enclosure

Empty freezer

Shut off power

Use two striaght screw drivers to hold the electrical connector clamps open

Remove connector, noting which wire colors were from top to bottom

Remove clamp screw under the enclosure

Remove the Yoke from the motor. It is attached by a left handed thread. Tapping with a small hammer may be necessary to free the locked position. Keep the washer safe.

Remove screws from ther motor, the solenoid, and the plastic solenoid armature cover.

Fit the motor and solenoid to the new enclosure, using existing screws.

Fit the Yoke on to the motor shaft.

Attach the solenoid to the enclosure.

Slide the armature into the solenoid, and screw the armature guide and cover into place.

Test movem,ent of the solenoid armature by hand, to ensure free movement.

Attach a string loop to the end of the connector so that it stays at the top while the enclosure is put into place.
Slide the enclosure in, reconnect, add retaining screw.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used:
  • Ice Enclosure
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: Michael from Cedar Key, FL

Motor separated from encloser (broken plastic)

Disconnected power to frig.
Had to wait for "ice block to defrost in ice bin and enclosure before removal. Caused by water from a frozen water tube overflowing into bin. This in turn "locked" the screw in place causing the motor to break from its mount on enclosure when trying to get ice.
Removed broken enclosure,one screw on left side and lift out leaving motor hanging. Disconnected wiring marking where they would reattach removed other part from enclosure. Unsnapped wiring harness from back wall.
Removed yoke from motor. Easier than I thought . A light tap with a hammer (right side with yoke facing you) it spun right off.
Attached wiring to parts and then installed parts to enclosure. Tapped yoke with hammer again. Repositioned encloser and from under reached up and plugged in the harness into the back wall.
Mounted encluser and ice maker.
Ice maker is up and running.
Will pay more attention when screw is bound up and not from blocked dispenser.
Thanks for Part and How to section..

Help other customers find the most helpful instructions.

Were these instructions helpful?