2060289-1-S-Whirlpool-61004881-Ice Enclosure
2060289-1-S-Whirlpool-61004881-Ice Enclosure 2060289-2-S-Whirlpool-61004881-Ice Enclosure 2060289-3-S-Whirlpool-61004881-Ice Enclosure

Ice Enclosure

PartSelect Number PS2060289

This is the tray that holds the ice dispenser.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Compare At

    $102.36
  • You Save

    $17.06
  • Your Price

    $85.30
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 10 reviews What's this?
1-10 of 10
 

30 of 31 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

Customermark from marietta GA

Ice-maker had ice, but did not dispense the ice when pushing in the button.

First I removed to ice-bucket and noticed the plastic that holds the motor with a head of what I would call a two-prong fork had broken off the plastic (enclosure). Thus it lost contact to the ice bucket's screw that pushes the ice forward when the dispense button is pressed. After ordering a new enclosure I had to remove one screw nut and pull the wire plug (to the motor) out carefully. Then I had to remove eight screws holding the motor and related parts to the old enclosure and attached it to the new enclosure. The only tricky part was taking that fork off. It screws off, but in the opposite way. Also, I had to get a pair of pliers to hold the turn shaft from turning when taking the fork off.

Help other customers find the most helpful instructions.

Were these instructions helpful?

23 of 23 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Wrench set

CustomerMichael from Alpharetta GA

Plastic tray which holds the ice depenser motor broke

The motor had broken loose from the plastic enclosure, so I first unplugged the motor from the power supply in the rear of the freezer compartment in order to remove it from the freezer. I then removed the four screws which held the motor against the plastic enclosure. I also removed the screws which hold the plastic enclosure to the freezer compartment.

The most difficult part of the repair was removing the 2 pronged fork from the shaft of the motor as it was reversed threaded on the motor. I held the motor in place on while using two pair of pliers to remove the fork from the end of the motor shaft. I used one pair of pliers to hold the shaft in place while using the other pair of pliers to turn the fitting in the opposite direction.

Once this was off, it took only 5 minutes to reattach the motor to the new enclosure and place it back into the freezer. Total repair time was about 30 minutes because I had to figure out how to get the fork off of the motor shaft. Everything else went very smooth. The new part fit perfectly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 14 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerJohn from Virginia Beach VA

Motor for turning coil that ejects the ice detached from the ice enclosure due to cracked plastic on the enclosure.

1. Removed ice bin.
2. Removed vertical panel next to ice bin by sliding two top supports off of support posts and pulling the panel out and up.
3. Removed screw on left side holding ice enclosure in place.
4. Pull ice enclosure out about six inches and tip back end down exposing electrical connector.
5. Detach the electrical connector by pressing the release tabs on the top and bottom of the connector.
6. Removed ice eclosure by pulling it up and out.
7. Detached motor (4 screws) and relay (4 screws) from plastic enclosure. Make sure to keep track of screw positions since they are not all the same size. Use same positions to reassemble.
8. Hold shaft of motor with needle nose vise grips and remove the "U" shaped end piece by turning it clockwise. A sharp rap with a screwdriver handle breaks it loose. Pay attention to the orientation of the washer under the "U" shaped piece (the raised inner edge next to the shaft goes against the "U" shaped piece.
9. Attach the motor and relay to the new ice enclosure paying attention to the screw position.
10. Put the washer on the motor shaft (raised side up) and screw on "U" shaped piece (counter-clockwise).
11. The rest of the installation is a reversal of the removal process.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 11 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerCarl from Gurnee IL

Auger motor broke off of ice maker enclosuer

Very easy to remove one screw holding the enclosuer, then unplug the wire harness, remove 4 screws holding the solinoid, and the 4 screws holding the auger motor. The hardest part was removing the auger from the shaft of the motor. this took most of the time. reassembly went very fast.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerLou from san antonio TX

Broken tray

Remember the bolt holding U piece is reverse screw off.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerMichael from Vienna VA

Automatic ice maker stopped delivering ice through the door dispenser

The driver that turns the screw broke off the ice enclosure. I removed the side panel, removed one screw underneath the enclosure, unclipped the wire harness and removed the entire enclosure.

I did one unnecessary step and removed the magnet from the housing. Better to remove the entire housing, then transfer the motor and magnet to the new housing.

I noticed that others had problems unscrewing the drive unit (which you need to do to transfer it to the new housing.) I simply held the center hub with a pair of pliers, and gave the drive one tap with a hammer. Like the other reviews, note that it unscrews opposite way.

Reassembly was quicker and easier; just undo everything you did to get the housing out of the freezer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerPat from Clarkston MI

The ice maker enclosure was broken

This was the easiest project of the Holidays. Literally saw the part was broken, went on-line and ordered the part and in a few days it arived at my door. Removed a few screws, unplugged the electrical connector and transfered the motor to the new part.

Saved me a few hundred dollars the repairman would have charged!

THANKS

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Wrench(Adjustable)

CustomerTravis from Westchester CA

Damaged ice enclosure tray

Removed the four screws around the shaft. Removed the support nut on the underside of the enclosure. Pulled the enclosure out of the freezer. Removed the "blade" from the drive shaft - This was somewhat difficult as others have described. Needle-nose vice grips are almost a requirement or you'll never get it off. (Turn clockwise to remove it, as the threads are reversed). Attached the motor to the new enclosure with the four screws. Replaced the enclosure and screwed in the support nut on the underside. The difficulty in this whole process by far is removing the blade from the shaft. It takes a lot of force. At one point I almost gave up thinking that it was manufactured or pressed on. It finally came loose, and then the reinstall was no problem. My suggestion would be to let the motor and parts heat up to room temperature for a bit. It may help. A little spray of WD-40 may help as well.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerChet from Marietta GA

Ice dispenser auger broke loose from ice enclosure

I followed the directions from John from Virginia Beach, with the added warning: Unplug the electrical connection and bring the whole ice enclosure out before you remove screws holding the relay and motor to it so you can see how it goes together. When you remove the relay, notice that a metal cylinder (Michael from Vienna Va calls it a magnet) slides out of it. If possible, keep this unit together. If it comes apart, notice there is a spring on this metal rod. Don't lose the spring and remember how it all goes back together. This job was just as easy as it should have been.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 9 people found this instruction helpful

Parts Used

  • Ice Enclosure

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerGregory from Auburn CA

Plastic housing broke, that holds motor

followed blog left on your site.
job was easy except for housing
that you reverse thread off. used visecrips
which helped. otherwise no problems.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-10 of 10