| |
13 of 19 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerStan from Clovis NM
Control board shorted out making it inoperative
removed ice and water dispenser to get to control board and removed two screws and electrical plug and two other wires and remove c/b then replaced c/b and all wiring and screws put it back togather in appro. 25 to30 mins.
|
10 of 17 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
CustomerCarole from Magalia CA
Water and ice dispenser would not work
I hired a repairman and it just took him a few minutes to take off the dispenser panel and install the parts. He put everything back and the green light came on. We drew out a couple of glasses of water and everything seemed to work fine. Then before he left he said "let's try it one more time". He put a glass under the water dispenser, pushed the button, something popped and would not work. He took the panel off again and checked the new part and the control board was burned out. It had a black mark on it. We don't know what happened and neither of us know how to find out what happened. Could you please help me. Thank you, Carole Prinz
|
6 of 7 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsPliers, Screw drivers
CustomerWing from Stockton CA
Control board and fountain backet damaged by burned out solenoid.
Removed damaged fountain bracket by removing the torx screw using torx head screw driver. Install new control board and new solenoid onto the new fountain bracket using existing screws. Reinstall fountain bracket to the freezer door.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers
Customeroliver from sebastopol CA
Ice dispenser main board was fried
I replaced the broken and fried parts. And everything works great now
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerKevin from Mukilteo WA
Fountain broken
Fried the new circuit board, dead short somewhere.
|
3 of 9 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerStephen from West Caldwell NJ
F0 error message - oven won't heat
Removed front display panel by removing 3 screws with nut driver. Removed ERC control board from display panel by removing 2 screws. Labeled all wires according to the terminal description on the existing board (this is important as the new control board terminations are in different places than the existing one. Disconnected wires. Removed keying sleeve from 2 wires since the new control unit was keyed differently. Connected wires to the new control board. Re assembled board to display panel and panel to oven. Works great.
|
1 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers
CustomerRandall from Cleveland TN
Ice dispenser door would not open
I had previously ordered the solenoid and door kit. The instructions were very well done. The pictures were a bit blurred but have been recopied several times however were adequate to see approximates on where things were. I removed solenoid and replaced it and the door flapper for ice dispenser. No problems with any of that. I had to work with the spring a little, I should have paid more attention to how many times to wrap it for the correct tension. However the solenoid was not the problem. There was intermittent operation from the solenoid when I would jiggle the pc board. Probably has a bad solder joint on the board. I ordered a new board, it took only 10 minutes to replace it since I was familiar with taking the housing loose. Put it all back together and it's working great. There was no drawing or instructions with the pc board but there were in the solenoid kit I had gotten first.
I do highly recommend Parts Select. Parts were shipped promptly. Matter of fact when I ordered the pc board early on Monday. I received it Tuesday afternoon with just ground delivery.
Very Happy Customer. Thanks Parts Select.
|