Turntable Drive Motor

PartSelect Number PS2055102

This motor rotates the glass turntable in the microwave.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Tray won’t turn.
  • Compare At

    $58.04
  • You Save

    $9.67
  • Your Price

    $48.37
In Stock
Order within the next 3 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 8 reviews What's this?
1-8 of 8
 

39 of 40 people found this instruction helpful

Parts Used

  • Turntable Drive Motor

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerTim from Oviedo FL

Turntable on maytag mmv5100aaw stopped turning

Symptom: Turntable stopped turning. Was able to remove the glass tray in the microwave and the little cam that drives the glass tray was barely turning. Control on microwave to turn the turntable on/off was working as evidenced by the cam not turning when I turned off the turntable. When I turned the cam manually, I could feel the motor turn so I knew the CAM and motor shaft were not stripped.

Repair Procedure:
1) Unplug the microwave.
2) Remove the 4 screws from the bottom of the microwave while holding the bottom cover so that it does not suddenly drop. It is not very heavy so you are fine to hold it with one hand and unscrew the screws with the other. Don't drop it as it has a glass lens for your lights and two light bulbs that light up the cooktop below.
3) Swing the front of the cover down slowly. You wil notice that the back is held in by tabs that slide into the back of the microwave. The bottom cover comes off very easily with some forward motion to dislodge the tabs.
4) Now look up under the bottom of the microwave(assuming your microwave is mounted over the range like mine) and you will see the turntable motor (GEAR MOTOR) in the center.
5) Carfully remove the two wires from the motor by gently working the connectors off of the motor using neegle nose or regular pliers. Don't grab the wires as you may pull them out of the connectors. Work with the connectors on the motor terminals. You will find the job much easier to do if you also remove the wires from the light housing. This will allow you to set the bottom cover aside and will give you greater access to do the job.

NOTE: Now is a great time for you to clean the filters, filter slots, bottom cover, and the light lens. A lot of grease can accumulate on the bottom of the microwave if it is mounted over a range (like mine). If you remove the light assembly, you can clean the cover, filters, and and light lens in the sink. Make sure that you dry all components thoroughly before re-assembling.
6) Make a note of which wires go to which terminals on the motor and the lights.
7) Remove the two screws from the motor and remove it. Note that there is a little plastic insulator film, a very thin washer and a bushing associated with the motor. You will want to re-install these with the new motor. Replace the motor with the new one being careful to put the other pieces back in place as well. Note that the little black turntable cam has a tab on one side so if you want to put it out of the top, you will need to tilt it slightly.
8) With the motor and associated parts back in and secured with the two screws previously removed, re-attach the wires to the lights and motor.
9) Replace the cover and screws and you are done!

This repair is much easier than these steps would suggest but I wanted to be thorough.

I called Maytag and they refused to sell me the part because they said it was dangerous for the user to replace it - rubbish. As long as you kill the power to the microwave and confine your work to the bottom of the unit as described, you will be fine. Maytag wanted to send out a repairman at $80 just to show up. I did the entire repair myself in about 15 minutes for about $40.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Turntable Drive Motor

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerCHARLES from HOLCOMBE WI

Turntable motor was bad.

fliped it upside down and took of the panel un screwd the motor and un hooked the wire leads.then revesed the process.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Turntable Drive Motor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRichard from Spokane WA

Turntable quit working

Removed the 4 screws holding the base of the microwave, it was mounted over the stove. Unpluged the wires from the motor, removed 2 screws holding to motor to the underside of the stove. Removed the motor and replaced it with the new motor, replaced the 2 screws, replaced the bottom cover, and started the oven. The turntable worked / revolved once again. WAL-LAH!

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Turntable Drive Motor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerClyde from Greensboro NC

Turntable stopped turning.

Removed bottom panel, disconnected power wires, removed and replaced motor with new part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Turntable Drive Motor

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerTeril from Wetumpka AL

Turn table would not rotate gear was bad

Very easy to remove the bottom on the Microwave. Make sure you have unplug the electrical cord. Take the screw driver remove three screws and use your pliers to remove the two wire terminals. Reverse the order and you have a new microwave that works great. Also if you are not using the tray in the microwave remove it as it heats up and takes away from the item you are trying to heat. Good luck to you!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Turntable Drive Motor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMichael from New Port Richey FL

Gear motor went bad

Took cover off 4screws motor has 2 screws pulled off 2 wires.Put new motor on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Turntable Drive Motor

Level of DifficultyVery Difficult

Time to do repair:Less than 15 mins

ToolsPliers

CustomerLinda from Maspeth NY

Unable to self-clean, lock not working

The repairman called me during the scheduled window of time and talked me out of coming over to fix it. So he never came over.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Turntable Drive Motor

Level of DifficultyVery Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers

CustomerRobert from Harrisonville MO

Turntable inoperative

Motor replacement was ok and could have been accomplished is less than a half hour.

Replaced turntable drive motor. Unfortunately, the problem was the turntable shaft (It was worn). The turntable shaft is no longer available. So, the problem is not yet fixed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-8 of 8