2052983-1-M-Whirlpool-56076-Idler-Pulley-Spring.jpg
2052983-1-S-Whirlpool-56076-Idler-Pulley-Spring.jpg

Idler Pulley Spring

PartSelect Number PS2052983

This metal spring fits onto the arm of the idler pulley assembly.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Compare At

    $24.17
  • You Save

    $4.03
  • Your Price

    $20.14
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.6 / 5.0, 9 reviews What's this?
1-9 of 9
 

83 of 148 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerBryan from Everett WA

Dryer would make hmming noise and motor was loud like there was some resistance. Dryer would overheat and shut down

I removed the covers, released the belt, pulled the drum, replaced rollers, glides, idler pulley and motor. The motor was the main issue but I replaced the rollers, idler and glides while I was in there. My biggest challenge was the clips that hold the motor in place. The hooked over a metal ear. I was able to use a big strait slot with downward pressure to release and reinstall.

The illustratations on the web site made ordering the correct part easy and the part fit perfectly so this repair job could have been accomplshed by anyone with very basic mechanical understanding.

Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 12 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

Tools

CustomerKATHLEEN from HUDDLESTON VA

Loud screeching sound ....needed motor instead!

I am a widow. Had to pay for labor. He said it was motor. I said I would think about it. I looked on line at your site. Found symptoms that pointed toward idler pulley wheel with bearing, etc. Your site said: ZERO PERCENT CHANCE LOUD SCREECHING WAS MOTOR! So I ordered all parts above. I called repairman to return; he assured me he tried it enough to be assured it was motor bearings. So, I placed another order with you for a motor. Repairman just installed motor, screeching is gone! We installed the belt, pulley, etc..few of the above parts since dryer is old. PLEASE UPDATE YOUR WEBSITE TO INCLUDE MOTOR (BEARING) AS POSSIBILITY FOR LOUD SCREECHING.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Wrench set

CustomerGeorge W from Austin TX

Progressively louder squeaky noise when drying

I followed the instructions found on this site. The hardest part was figuring out how to release the clamps at the front of the dryer so I could remove the top.

The key was to unbolt the clamps at the back of the dryer first, then to use a putty knife to release the two clamps at the front of the dryer that hold the top to the front.

The rest was easy by following the steps already listed on this site and removing the two front pieces, then the drum and replacing the parts. Putting it back together was simple since I placed things in order and had taken pictures with my cell phone as I went through the process.

The time I took, included vacuuming the inside of the dryer thoroughly. Now it runs like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Socket set

CustomerBruce from Frazer PA

Loud squealing noise

Loud squealing noise coming from the idler pulley. The pulley was not spinning freely on the shaft of the idler pulley lever to the point of putting a groove in the pulley and damaging the belt. To fix the problem replaced the belt, idler pulley, and idler pulley lever. Because I had the dryer apart also replace the following items. Drum support roller and drum slides.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerGreg from Virginia Beach VA

Belt noise/slipping even after replaceing worn motor assy

Unplug dryer. Remove lower panel.Remove dryer lent duct. Remove Thermostat fm fan housing. Remove Fan.Remove Fan housing. Remove Motor assy by sliding out, wires lay toward front, allowing room to replace idler pulley and spring. Use lock ring pliers to remove pulley from shaft. Grease pulley/shaft w/high temp grease [I used ultra-hi temp ceramic brake grease-can get in small packets at auto stores].Noise/slippage has all but stopped. Lesson: replace rear rollers and front felt/glides. Belt looseness also caused by worn rear rollers [smaller overall diameter from age]-even though they spin freely

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerLarry from Lima OH

Belt was worn - ready to break, decided to replace the parts that commonly go bad.

I removed the bottom panel, then the larger front panel that includes the door. After that, removed the top 2 screws so that the top would swing up (but not lift off). After that, I removed the front "bulkhead", and the drum. Then it was just a short matter of sweeping everything out, and replacing the parts one by one. Most came off with a socket, or snap ring pliers. Pretty obvious at this point...

Be sure to label any wires - I removed 5 wires all total, and wrote down the colors and where they went.

It's great to have help when working with the drum. BTW, you CAN replace the belt without taking out the drum, but you better have strong fingers to move the belt tensioner and slip the belt on it - all with one hand. I did it, but that was the least "fun" part....

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set, Wrench(Adjustable)

CustomerJoan from Philadelphia PA

Loud sharp noise when the dryer was spinning

I found a shrieking noise repair on this website, followed their instructions (winging it a bit) and was able to fix my dryer for the price of those parts - excellent!!! As the other instructions said, mark EVERY wire.
I have additional instructions - MARK EVERY SCREW you remove. I had 4 extras when I was finished and now I'm a bit worried about where they belong :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Socket set, Wrench set

CustomerJohn from Hamilton NJ

The belt tension pully bearing was worn out making a loud screech when in use.

I unplugged the dryer then removed 2 sheet metal bolts on the lower front access panel. The panel was removed and this exposed the duct for the hot air exhaust. I had to remove the duct to access the package for the motor and worn out pulley. I had to the remove 2 bolts in the bottom corners for the upper front of the dryer. The upper panel was then easily removed, 3 phillips screws had to be removed from inside the drum area on the back of the exhaust duct where the lint filter is inserted.
Once these are removed the duct cowms right out.
This exposes the motor and tension pully platform. I then reached in and moved the tension pulley to relieve pressure and took off the belt that drives the drum.
There are 2 botls at the front base that need to be removed then the platform can be slid forward and the rear tongue comes out of the groove. Rotate the platform 45 degrees and you can access the bolt and nut that mounts the pully arm to the platform. Once removed the spring can be removed and the assembly taken out of the dryer and parts switched over, There is a spring clip you will need to remove normally with a special tool but 2 needle nose pliers will work. Once the parts are replaced reverse the process. Putting the belt back on can be confusing lying on your back with one arm inside the dryer but persistance overcomes resistance,

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerKeith from Marietta GA

Drum would not turn with moderate to heavy load.

Removed the front dryer panels (lower & upper), front drum support and drum. This gave me easy access to the idler pulley and tension spring. I also took the opportunity to vacuum all of the lent that had collected over the years. After installing the new parts and aligning the belt, I reassembled the panels, plug it in and it worked like a champ! Locating the parts on your website was fast and easy. I appreciate it and thank you.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-9 of 9