2047676-1-S-Whirlpool-53-0148-Door Switch
2047676-1-S-Whirlpool-53-0148-Door Switch 2047676-2-S-Whirlpool-53-0148-Door Switch 2047676-3-S-Whirlpool-53-0148-Door Switch

Door Switch

PartSelect Number PS2047676

This dryer door switch contains three metal terminals. It is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.
  • Will not shut off.
  • Compare At

    $17.08
  • You Save

    $2.85
  • Your Price

    $14.23
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Door Switch Kit

Part Number 2162265

This kit includes the switch and mounting clip.

$15.20
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 4 reviews What's this?
1-4 of 4
 

12 of 16 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerJesus from Hillsborough NC

The door switch broke and dryer would not run

1. Removed wires to switch
2. Lifted top panel of Dryer with a screw driver
3. removed two inside screws holding the from panel against the drum.
4. Dropped front panel on the floor and removed door switch.
5. While the door was out, I removed the lint panel attached to the door - two screws.
6. Cleaned the door panel with a vaccum cleaner
7. replaced lint panel onto door with two screws
8. replaced door switch to the front panel
9. placed front panel on to the from of dryer with two screws.
10. Connected wires onto the door switch.
11. Closed top dryer panel and them pressed hard to catch on to metal clips.
12. Attached Dryer cable to electrical outlet
13. Trurned Dryer on and open door as it tumbled to confirm it would stop.
14. Done

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 24 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerGwen from Chinagrove NC

My dryer was completely dead

I checked this site and determined all of the possible causes. I watched the video when available. I checked prices on a replacement set ($2300.00) if I got what I really wanted but decided to tackle the repairs myself and save $2100.00. My only mistake was becoming distracted when testing the timer resistor before placing my order and not knowing where to connect the replacement. I ended up paying for assistance online ($24.00). It was much cheaper then replacing my washer and dryer or even calling a service person out for help. I applaud the services offered at this site and would recommend it to friends and family.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Door Switch

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerLawrence from Jacksonville Beach FL

"door open"" message

Remove back plate covering the control module, exposing screws. loosen screws removing control assembly. Without disconnecting anything, move assembly out of the way, exposing the door switch below. Loosen screws at each side of the front panel to allow access to door switch. Disconnect switch and replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerPreston from Port Saint Lucie FL

Blower wheel broken

This is a very easy, no frills dryer to work on. Access to the blower by removing two screws holding the front panel. Blower fan held in place with a snap ring. Just recently replaced the drum rollers and shafts and the belt as well. It ran sweet for about a week and then an electric control on the motor went bad and it on;y can be replaced by buyig a new motor at $135.00. Some luck huh? Found a guy local selling a 8th month old Maytag of higher capacity and more bells and whistles for $150.00. It works great and my old Admiral uses many of the same parts so I'll have a supply of thermostats, rollers, etc., when the Maytag goes on the blink.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4