| |
11 of 14 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:1- 2 hours
ToolsNutdriver, Pliers, Screw drivers
CustomerDaniel from San Diego CA
Noisy blower wheel
I first unplugged the unit, unlatched the top cover, removed the wires for the door switch, then removed the two screws securing the front panel. I "propped open" the top lid with a 2 by 4. I then lifted away the front panel, removed the blower housing screws to expose the blower. Then I removed the snap ring on the blower shaft, the clamp holding the blower wheel in place, and slid the blower wheel off the motor shaft. Reassembly was in the reverse order. Was very easy.
|
11 of 15 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsPliers
CustomerRoberta from St. Louis MO
Dryer had been noisy, then stopped heating.
Opened dryer and removed drum. Replaced old blower wheel with new wheel, clamp and clipwhich was worn and was responsible for the noisy operation. Plugged in new ignition coils then replaced drum. Dryer works great now.
|
4 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers, Socket set
CustomerLawrence from Clifton Forge VA
Blower wheel broke and makeing loud clunking noise
1st thing,,,,unplug dryer from electric,,,Raised the top of dryer, took 2 screws out that held front of dryer on, removed 3 wires and dropped front of dryer. exposed blower wheel,, removed all nuts holding front of blower wheel, removed clamp on front of wheel with pliers, removed old wheel, replaced everything in reverse.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsPliers, Socket set
CustomerDonna from McCloud CA
Blower wheel broke
Lifted hood ,and took two screws and tilted the front back and remove the door switch , and took front off ,use little socket set, took cover off fan housing took pliers removed clamp on fan , remove key way on end ,slid fan off and put new one on and reverse the way if came off.
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
CustomerSue from Hardeeville SC
Loud bumping on start up, noisy running
Unplugged, loosened front cover, disconnected two wires from door open indicator, removed front cover with screw driver. Removed air flow cover with screw driver. Used pliers and retaining ring pliers to remove old blower wheel, my husband calls it a "squirrel cage". Installed new blower wheel and reassembled. It was all easy to see and get to. Thanks for having the right part. Sue.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsWrench set
Customerrobert from sanford NC
Noise
the same way it was described on your site, this dryer is nearly 17 years old, I've needed to change this at least 5 times.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers, Screw drivers
Customercraig from Mckinleyville CA
Loud clunking noise while running dryer, then noise went away and not much air blowing out
first pryed up the dryer top, pulled the two wires for the door switch and removed front panel. remove 8 or 10 blower housing cover 1/4" screws. removed blower moter shaft snap ring pulled out damaged blower wheel. slid on the new wheel with the flats on the shaft and new wheel alighned up. installed blower clamp around blower stub. installed motor shaft snap ring. reinstalled blower cover cover. installed front dryer cover to include installing door switch wiring. put down top and pushed dryer back into place making sure to install the blower vent hose. started dryer to test operation. all worked well the first time.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers, Socket set
CustomerRichard from Opelousas LA
Blower wheel broke off of shaft.
Purchased a new blower wheel from you and installed.
The part was exactly what I needed and was delivered ahead of schedule. Ordering over the internet was easy and straight forward.
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerErik from Lancaster PA
Dryer would not dry the clothes
|