2046273-1-S-Whirlpool-503979-Cycling Thermostat
2046273-1-S-Whirlpool-503979-Cycling Thermostat 2046273-2-S-Whirlpool-503979-Cycling Thermostat 2046273-3-S-Whirlpool-503979-Cycling Thermostat http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/31219.gif

Cycling Thermostat

PartSelect Number PS2046273

This cycling thermostat has a limit of 153 degrees Fahrenheit, meaning that your dryer will cut out when the internal temperature reaches 153 degrees. It kicks back in when the temperature drops by 15 degrees Fahrenheit.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Too hot.
  • Takes too long to dry.
  • Shuts off too soon.
  • Compare At

    $25.20
  • You Save

    $4.20
  • Your Price

    $21.00
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 11 reviews What's this?
1-5 of 11
 

17 of 24 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Socket set

CustomerEric from Yorba Linda, CA

Dryer stopped working with no power detected

Based on my research, the thermal fuse could be blown out so I tested it and it was. I've replaced the thermal fuse, high-limit thermostat and cycling thermostat. bam! it's up and running again. I'd highly recommended ordering your parts thru PartSeclect..the order was easy and shipping is quick. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 18 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Socket set

CustomerDonald from Madison, WI

Dryer shut down before clothes were dry

... I figured it was some over temp switch but then read about the gas solenoid problems others were having... bought $100.00 worth of parts... saved the old just in case down the road I might need them... figured a service call would cost me that much... now lots of new parts... and a working dryer. Done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Socket set

CustomerGene from Encino, CA

Dryer would cycle on once then wouldnt continue to heat to dry

I first unpluged the dryer then removed the bottom cover (two screws) then found the correct socket and removed the components and replaced them wire for wire. PLugged it back in and strated the dryer and watched the process. Unforunately it cycled twice and then stopped working. I went to a local appliance store to buy another high limit fuse because I thought it blew and happened to talk about the situation to a man behind the counter and he insisted it was the gas coils so I bought some and replaced them and its working fine now without replacing any more components. Im not a aapliance repair man but mechanically inclined but experience does pay. Hey, everything is easy if you know how...

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Cycling Thermostat

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerJeffrey from Morris, IL

Cycling thermostat failed

DIAGNOSTICS: Unplug dryer to reset controls. Remove lower cover. Plug back in. Start dryer. If flame starts and goes out in a few seconds, probably the cycling thermostat (located centrally near bottom of dryer) is bad. It fits in the center of the thermostat heater (not replaced). Use the on-line schematic. I reset the controls (as above) again and jumpered the cycling thermostat. This time the flame stayed on. I turned off dryer before High Limit Thermal Fuse could blow out. Only a trained electrician should do the above.
REPAIRS: Decided to remove main cover, to get better angle on thermostat screws. Unplugged. Removed door first. Be gentle with wires. Be careful with drum, it will simply fall out if jarred. Remove two screws for cycling thermostat. Remove wires, replace cycling thermostst. Reassemble. Be sure drum is still on rollers on back and anti-friction strips in front.
SHORTCUT: If you use an articulated socket wrench on the thermostat screws, you can save your self the trouble of removing the front cover, door, and possibly drum.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 10 people found this instruction helpful

Parts Used

  • Cycling Thermostat

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsWrench set

CustomerMichell from Inglewood, CA

My heater would not heat!

I asked the Gas Co. if they can come out and relight the pilot to my dryer... (which is common for gas dryers) He tested the equipment and told me that the thermostat was the problem. Most places was looking for around $160 for parts and labor. Well, I saved around 130, as I just simply replaced the thermostat. DONE DEAL!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 11