2045752-1-M-Whirlpool-500092-Single-Felt-Pad.jpg
2045752-1-S-Whirlpool-500092-Single-Felt-Pad.jpg 2045752-2-S-Whirlpool-500092-Single-Felt-Pad.jpg 2045752-3-S-Whirlpool-500092-Single-Felt-Pad.jpg

Single Felt Pad

PartSelect Number PS2045752

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Compare At

    $4.69
  • You Save

    $.78
  • Your Price

    $3.91
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Drum Glide

Part Number 2039613

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

$3.91
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 11 reviews What's this?
1-11 of 11
 

55 of 64 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerJeffrey from Medina OH

Noisy - clothes getting stuck between drum and bulkhead

1) Removed lower panel
2) Removed door
3) Removed Front Panel - removed connectors from switch and marked connections
4) Removed Front Bulkhead
5) Glides and Felt pads were missing, and brackets were nearly worn through
6) Removed and Replaced old brackets
7) Attached self-adhesive felt pads
8) Attached Drum Glides
9) Removed old felt seal
10) Glued new felt seal in place with 5-min epoxy
11) Allowed Epoxy to set and stop stinking
12) Re-attached front bulkhead
13) Re-attached remaining parts

Dryer works great, is quiet again, and no longer eats clothes!!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerBilly from Woodsboro TX

Felt pad on cylinder glide bracket came off.

First, leaned dryer back and removed 2 screws at bottom front panel.
Then removed 2 screws at bottom of door assembly.
Pulled bottom door assembly forward and down.
Disconnected "can't go wrong" wiring connectors.
Then removed old cylinder glide rivets at bottom of cylinder using drill motor with 1/4" drill.
I installed new felt pads on new cylinder glides. Then installed glides with rivet gun.
Reconnected wire harness.
Installed door assembly and lower panel assembly.
BACK IN BUSINESS! THANK YOU!!!!!!!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerTroy from Reading PA

Cylinder glide brackets broke, cylinder seal damage

After removing the front of the dryer, I took out the front assembly where the seal and glide brackets attatch. I replaced the bad cylinder glide by drilling the old rivets out and re-riveting the new glide in place from the back side. I then replaced the felt pads and glides on the glide brackets and glued a new cylinder seal around the front assembly. I reccomend having 4 hands for placing the cylinder seal around the assembly with fresh glue.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsSocket set

CustomerRita from brewster WA

The glide bracket had been warn nearly in half

1. I removed the lower front panel.
2. Carful remove the front door making not of which wires whent were of the switch
3. Removed the front bulkhead.
4. Drilled out the rivits that held the bracket in place.
5 Use a pop rivit gun and 1/8 in pop rivit and washer.
6 Installed the felt pad and the drum guide.
7 Put the whole thing back together.

I love your web site the exploded diagrams make fixing my dryer quite easy. I do it. so for under $50 my dryer is almost like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerGregory from Virginia Beach VA

Noisy belt/slipping intermittantly

Unplug Dryer. Remove lower and upper front panels [remove wires from upper right door switch]. Lift up on belt idle pulley and take belt off pulley/motor.Remove Front Bulkhead and dryer lint/vent ducting. Note position on drum and remove belt. Unbolt top panel front 2 screws to allow room to remove drum.Remove drum. Take lock rings off Drum support rollers and remove old rollers. Clean roller shafts and apply hi-temp grease [I used ultra hi temp brake grease-ceramic based-small packet can be purchase fm auto parts store]. Re-install new support rollers and lock rings. Re-install drum and slide belt back into position. Remove and replace felt pads and glides into inside of Front Bulkhead. Reinstall Front Bulkhead and top panel [connect door switch wires].Install belt around idle tension pulley. Re-install lower panel.All parts fit perfectly and delivered quickly.Belt had just been replaced previously.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerJack from Nashwauk MN

Felt seal was shredded and glide bracket was worn through

The on-line video showed the dryer top being loosened from the front as the first step. On our dryer, the bottom panel in the front needed to be removed first - two screws, then the front panel(with door)- two more screws and two wires for the switch. Next was the front guide panel - four screws. The glide brackets bolted to this panel and the felt seal was glued to it. Reverse the process to put it all together, and my wife was happy again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerGregory from Odessa MO

Drum made a lot of noise and the drum turned hard

Removed top and front panels, reached in by motor and removed belt from motor, removed drum and replaced slids and back drum wheels. re-assembled the front and top.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDoug from Corning AR

The brackets that support the front side of the tub were worn out and one of them was worn in two

I started at the bottom and removed the two nut screws that support the bottom section of the front of the dryer. Then I removed the two nut screws that supports the next section and disconnected the two wires ( making note of wich terminals each wire went to). Then I removed the lint trap housing( three phillips head screws hold it in place from the inside). Next ,I removed the face plate( held in place by 4 nut screws and two metal tabs at the bottom). Then I took the old tub brackets and felt seal off of the face plate . Next ,spray adheisive arond the ring of the face plate and install the new felt seal, then the new brackets and dryer glides and felt pads. Last, re-install all components.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerMike from San Clemente CA

Worn out bushing in support roller, dryer glides and felt disinigrated. Worn out felt cylinder seal

Unscrew front, detach electrical, tilt back top, remove drum. remove retaining ring and glide, replace ring and guide remove old felt seal, adhere new felt seal with contact cement, remove what was left of felt pads, replace pads and new glides, reassemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 500 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerChad from Caldwell ID

Dryer made marks, then noise, then more noise

Thanks to this website we were able to not only find the parts, but a video that told us how to take the dryer apart. Unfortunately, between the time we diagnosed the problem, ordered the parts, and they arrived, the drum had worn into the front bulkhead. We were able to file the sharp parts dull and install the brackets, felt pads, and drum glides along with the felt seal, but ended up breaking the dryer door switch. Once that came in, it has been working. I'm not sure how long the repair will last, but it was much better than buying a new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 644 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

Customerjoe from johnsburg IL

Lots of noises

disassembled found bunch of worn out parts . I went to website wich was very helpful found all . my worn out parts online. dryer is very quiet now I wish i would have done it sooner.P.S. going to fix my dads dryer next. thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-11 of 11