High Limit Thermal Fuse

PartSelect Number PS2041343

Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do need to replace it. It's letting you know that something is wrong with your dryer.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Will Not Start.
  • Takes too long to dry.
  • Too hot.
  • Shuts off too soon.
  • Compare At

    $6.00
  • You Save

    $1.00
  • Your Price

    $5.00
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Limit Thermostat

Part Number 2177455

This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 225 degrees Fahrenheit. The element will kick back in when the temperature drops to 185 degrees Fahrenheit - the differential of 40 degrees.

Order within the next 9 hrs and your part ships today!
$24.38
In Stock

Fuse Kit

Part Number 2174577

This fuse kit comes with a thermal fuse, a high limit thermostat, two lead wires, & four mounting screws.

Order within the next 9 hrs and your part ships today!
$44.49
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 50 reviews What's this?
46-50 of 50
 

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

Customerjennifer from Nashville TN

Dryer overheating - clothes have a burned rubber smell

This Web site is a treasure. I found it and watched the repair videos. First, remove the bottom panel on the front of the dryer, the one below the door. Then remove the door panel, detaching the signal and light wires. Be sure to mark them first, as to which is on top and which is first. Then I removed the drum panel, with the lint box attached - you only need to remove that from the drum panel if you want to clean the inside of it. Lastly I removed the drum. You have to take the belt off the roller underneath first. After taking everything off from the front, it's super easy to get to the fuse and thermostat in the back. The most challenging part was putting the belt back onto the roller. It has a spring, so you have to stretch it far enough so that the belt will fit around it. Be sure to watch the video to understand the configuration of the belt and roller. Good luck!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerScott from Hawthorne FL

Dryer had no heat

I pulled the heating element loose and layed it on the floor so I could see if the elements were heating. This required totally disassembling the dryer from the front including removing the drum. Then I bypassed the door switch so the dryer would run disassembled. Then plugged in the dryer and turned it on. Heating coils did not glow... Hmmmm. Put a meter across the two thermal switches mounted on the element assembly to find one of them was open. Ordered switch from PARTSELECT; ordered a belt too while I had it apart. Parts came very fast and reassembled with new parts. WORKS LIKE A CHAMP!!! Thanks Partselect!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 4 people found this instruction helpful

Parts Used

  • High Limit Thermal Fuse

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerSusan from Ashtabula OH

Wouldn't dry---no heat

Disconnected the electricity,removed lower front panel with socket wrench and located high limit thermal fuse Removed wires and unscrewed old part and installed new thermal fuse. I reconnected the wires and it works perfectly.Also vacuumed out the lower area to remove unwanted lint while I was in this area. I saved a $75.00 service call by fixing it myself.
.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 11 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerWilber from James Town OH

No heat from dryer

Had to replace a thermal fuse in the dryer. They had ran the dryer with the lint tube blocked which in turn blew the fuse. I tested the fuse with a ohms meter which showed no resistance telling me that it had shut off the dryers heater to prevent a fire. Ordered the correct from parts select. It was sent quickly. You must pop the top on this Maytag using a putty knife than remove the belt and drum to access the fuse. Installed new fuse reassembled dryer plugged it in and everything worked fine. Another job well done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

43 of 1295 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set, Wrench set

Customerrussell from anamosa IA

Would run but would not heat

removed front cover and top took drum out remove heating unit replced limit switch and fuse reinstalled installed new idler put new belt around drum installed drum replaced glides put top back on and front cover . then replaced boosting heater witch is on the blower also cycling thermostat

Help other customers find the most helpful instructions.

Were these instructions helpful?

46-50 of 50