2041342-1-S-Whirlpool-40113601-Roller Bracket and Shaft Assembly
2041342-1-S-Whirlpool-40113601-Roller Bracket and Shaft Assembly 2041342-2-S-Whirlpool-40113601-Roller Bracket and Shaft Assembly http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/58910.gif

Roller Bracket and Shaft Assembly

PartSelect Number PS2041342

This part is used to hold the drum in place while it is rotating on the support wheels.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Will not tumble.
  • Compare At

    $23.53
  • You Save

    $3.92
  • Your Price

    $19.61
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Drum Support Roller

Part Number 2039408

This roller is for square-ported models and has a metallic bearing in its center. They are sold individually and most dryers use 2 rollers at the rear and it is recommended to replace both at the same time.

$8.93
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.8 / 5.0, 32 reviews What's this?
1-5 of 32
 

413 of 418 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerSteven from Holderness, NH

Squeeling and grinding noise

Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.
Followed other people's excellent instructions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer.
The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

203 of 278 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Socket set

CustomerWilliam from Round Mountain, NV

Squeeling/screeching

First I read all of the other stories about this problem so I would have the correct parts. At $6 a roller, decided to get all 3 & a belt. Pulled the lower panel off (2 bolts), then the door (2 bolts). Marked the door switch wires. Took 2 bolts out of the top & tilted it back. I found this the easiest way to access the drum. Mark 2 wires before disconnecting them from the top. All bolts are 5/16". Removed the plastic piece that connects the lint trap to the blower (3 screws). Have to access these from inside the drum. Removed the belt, then the drum. The bad roller was the belt tension roller. Can't get to the snap ring from the front of the dryer for this roller. The 2 rollers in the back you can get to without removing the drum completely. Very easy to replace all rollers with the drum out. Also very easy to re-assemble. Buy or borrow a good set of snap ring pliers. Make sure you diagram the proper belt route if you don't have a picture. I printed a picture off this web site. Have someone hold the drum up so you can get the belt on, otherwise the entire repair is a 1 person job. Went back together in about 10 minutes. Total cost $40.00 parts & shipping.

Help other customers find the most helpful instructions.

Were these instructions helpful?

128 of 195 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerDavid from Underwood, IA

Loud banging sound. Worn out roller.

Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all.

Help other customers find the most helpful instructions.

Were these instructions helpful?

86 of 151 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerBryan from Everett, WA

Dryer would make hmming noise and motor was loud like there was some resistance. Dryer would overheat and shut down

I removed the covers, released the belt, pulled the drum, replaced rollers, glides, idler pulley and motor. The motor was the main issue but I replaced the rollers, idler and glides while I was in there. My biggest challenge was the clips that hold the motor in place. The hooked over a metal ear. I was able to use a big strait slot with downward pressure to release and reinstall.

The illustratations on the web site made ordering the correct part easy and the part fit perfectly so this repair job could have been accomplshed by anyone with very basic mechanical understanding.

Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

28 of 33 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set

CustomerJOHN from CORPUS CHRISTI, TX

Dryer would squeal when drying clothes

Unplugged dryer, turned off gas, raised front of dryer with two 2X4's on edge resting on legs, removed two lower panel screws, removed lower panel. Removed lower blower & filter assembly, screws (3) are on the inside of drum. (Good chance to clean it out) Removed two lower front upper main panel screws. Supported top panel with wood for access. Removed panel slowly, marked wires that go to door switch, set panel aside. Removed tension on belt by reaching in on the right lower side and unhooking the tensioner from belt, look to see how it is installed, for reinstallation on assembly. Pulled drum out slowly as not to damage seals on drum. replaced parts, attached with self tapping screws.(screws all the same size) reassembly in reverse order. Will need to put belt on drum before installing drum. Check drum alignment with rollers and seals. Used very small amount of high pressure grease on roller bracket and shaft assembly where the support roller shaft spins for lubrication. All's quiet. (Vacuumed out inside while dissassembled)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 32