Multi-Rib Belt

PartSelect Number PS2041323

At 93-3/8" in length, this flat dryer drum belt has 5 ridges and is 3/8" wide.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Takes too long to dry.
  • Will not start.
  • No heat or not enough heat.
  • Compare At

    $16.56
  • You Save

    $2.76
  • Your Price

    $13.80
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 93 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set, Wrench(Adjustable)

CustomerAnthony from Rochester NY

Dryer would vibrate and make a loud bad bearing sound.

I began by disassembling the dryer to diagnose the problem. I discovered the belt had been riding on a section of a broken idler pulley as well as wearing a groove into the idler pulley bracket. I removed the broken parts and went to the Internet for replacement parts. Three days later the parts arrived and I began reassembly. I found it a little difficult to replace the drum with the belt in position but found it much easier to recruit some assistance during this phase. Another factor with the difficulty was that I hadn't paid real close attention to the webbing direction of the belt around the pulley and there were no diagrams depicting the proper direction of the new belt. I did figure it out relatively quickly but would advise paying very close attention to parts positioning during disassembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerSteven from Longmont CO

Loud squeaking noise

Removed bottom front panel (two nuts)
Disconnected wiring to front door and removed
Remove the two nuts holding the top panel to the front and lifted top out of the way
Disconnected the drive belt from the motor
Lift the drum up and out of the machine
Replaced parts, cleaned cabinet and reassembled with new parts

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set, Wrench set

CustomerKEVIN from HARPSTER OH

Dryer making loud noise.

Was very simple after watching the repair video provided o you site. Went exactly as described. Will deffinately use your parts again and will highly recomend it to anyone else who needs parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Multi-Rib Belt

Level of DifficultyDifficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerDonald from Punta Gorda FL

Dryer drum stopprd

Basically, Followed the instructions in the Video for Belt replacement. I found out however that the Tensioner was also broken aand needed replacement, and this required the snap wring pliers. also spindle on motor was stripped and had to use "lockTite" to repair that. Overall was far better "doining it myself" than paying for repai service which would have cost several hundred $ in costs. This increased my confidence level to know that as long as parts are available I will always be able to repair this appliance!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerMike from Kremmling CO

Broken belt and idler pulley.

I followed the belt replacement video and voila, the job was done!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Socket set, Wrench set

Customerstephen from Bettendorf IA

String from a hoodie somehow got inside the dryer and destroyed one of the guide wheels

I had to disassemble the whole thing and figure out what I needed. The new guide wheel and belt installed easy. The only hard part was trying to figure out how the dryer went back together.

I'm work in biomed/maintenance field, so I'm used to taking things apart. This was the 1st time I've tackled somthing like this. If your reasonably handy you could do this too. It only cost $30 to repair which was much less than buying a refurbed one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Wrench set

CustomerRobert from Spring Valley WI

Pulley broke and belt

removed drum and motor and installed new parts. Very fast service on parts. Well be back if needed.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Multi-Rib Belt

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerJOHN from NEPTUNE NJ

Drum would slip and at times not spin

You have to take apart the whole dryer to get to the belt.Nut driver with cordless drill make it go so much faster.Unplug dry, take apart dryer and replace with olr belt with new belt.Takes about 20 minutes to do.plus I took off the two guide wheels on back of cabinet and greased everything.Works like brand new.I had a repair guy tell me I needed a new motor.If you can spin the drum by hand replace belt first.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerKeith from Marietta GA

Drum would not turn with moderate to heavy load.

Removed the front dryer panels (lower & upper), front drum support and drum. This gave me easy access to the idler pulley and tension spring. I also took the opportunity to vacuum all of the lent that had collected over the years. After installing the new parts and aligning the belt, I reassembled the panels, plug it in and it worked like a champ! Locating the parts on your website was fast and easy. I appreciate it and thank you.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerRebecca from Mansfield TX

Dryer was make a loud squealing noise.

Took the front off the Dryer removed the drum. Replace drum rollers, Idler pulley wheel with bearing, and drum belt them replaced drum belt and reinstalled the drum. Put the front back on the dryer job complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerAnthony from Newport NC

High pitched noise

I removed the top and the front of the dryer and I had done before, so that was not to bad, then I moved the drum forward just enough to get it off the rollers but did not remove it all the way in order to keep the belt in place. I removed the snap ring holding the wheels in place and put the new ones on. I put the dryer back together, unfortunately it did not fix the problem. I am now waiting on the idler lever arm to replace it. Hopefully, that will be the key!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerCarol from Pahrump NV

Belt didnot want to go on the back side of the pulley

Need two to pull the drum.Not heavy just hard to handle. Pulleys came out easy went back easy. Belt wanted to twist butfound that out quickly when it was running and making a noise.Took it off and put on the inside towardthe back of the dyer. No more noise. Now you have to put your hand on the dyer to see if it is running (sooooooo quite) Hope this helps.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set

CustomerArthur from Roscoe IL

Idler pulley was squealing.

Removed door and front panel. Removed drum. Removed idler pulley arm and spring. Removed snap ring and pulley from idler pulley arm. Reversed process to re-assemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerSteve from Howell MI

Noisey

Pulled bottom access panel of, pulled front door section off, pulled lint filter assembly out, pulled drum out, disconnected idler arm, installed new idler arm and wheel, new belt around drum, drum back in, front door assembly back on, then routed belt over idler arm wheel, lint assembly back on, bottom access panel back on. very easy job, the hardest part was pushing the new idler wheel over the new pulley lever, but with a few firm taps with a hammer it was on. *Tips...save the idler wheel washers and retaining clip from bad wheel and be sure to draw yourself a diagram of what color wires hook up where, in case you forget.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Socket set

CustomerLee from Braham MN

Made clanging noise

Lay"d dryer on back took it apart 5/16 socket and a snap ring plier, orderd parts on a friday afternoon, parts came tuesday 9:30 AM. orderd all glides and rollers as long as it was apart, glad i did they were shot, real easy to repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?