Multi-Rib Belt

PartSelect Number PS2041323

At 93-3/8" in length, this flat dryer drum belt has 5 ridges and is 3/8" wide.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not tumble.
  • Noisy.
  • Takes too long to dry.
  • Will Not Start.
  • No heat or not enough heat.
  • Compare At

    $17.04
  • You Save

    $2.84
  • Your Price

    $14.20
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 93 reviews What's this?
 

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerRandall from Hoffman Estates, IL

Load banging noise when drun turns

removed front cover 2 lower screws. once front cover was off, the front drum support bracket was visable. removed 4 screws that hold that in. the drum is now loose and not supported in the front. pulled drive belt tensioner back to release belt. removed 2 top cover screws to get more vertical room to lift drum out. once drum was out, i used a snap ring plyers to take retainer ring off to remove damaged rear drum support rollers. replaced both rear rollers. also replaced drive belt and door lamp. the bearing in the left roller had seized and torn a big hole thru the roller . assembled in reverse order. now drum is nice and quiet

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Multi-Rib Belt

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerMichael from Marietta, GA

Squeaky belt

Removal of the entire 2 front panels
Removal of the heat exchanger into the drum
Removal and replacement of the belt
Reinstallation of the heat exchanger, and both front panels

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerGrant from Manalapan, NJ

Dryer would not tumbel under heavy load

First unplug anf turn off the gas to the dryer.
1. Remove the 2 screws located at the bottom of the front panel.
2. Use a flat head screw driver to pry the top of the dryer lid. The clips are pretty strong. This allows the front dryer panel to be removed.
3. Remove the 4 screws that hold the front of the drum ring in place.
4. Slide drum belt off of motor. Not the belt path before removing it.
5. Remove drum. This will give you complete access to the dum support roller.
6. This is a good time to vaccum the inside of the dryer.
7. You will need a pair of snap ring plyers to remove the snap ring that holds the roller in place.
8. Replace roller.
9. Reverse installation.
10. It runs great and has not been the quite in 10 years.

I would definitely use Parts Select again.
The parts shipped quickly and correctly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerDavid from Richland, MO

Dryer not heating

i am sorry i dont know all the technical term but here it goes, first I turned of the electrical breaker to the dryer, I unpluged the dryer and disconnected the dryer hose to the outside of home, I removed front dryer panel, remove front of drum panel, removed belt and found it to be worn, removed drum, removed the wiring connected to the back panel that had heating element inside, removed the back panel, removed the heating element inside the back panel and then reassembled unit. I had question whether or not it would ever run again, but it is working fine. Thank you for your prompt attention with sending the parts. i dont know if there was a different way to solve this problem, but i felt if there was an expection plate on the side of the unit, it would be helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerMichael from North Hampton, NH

Won't tumble with clothes & making loud noises

Dryer would only tumble for ~15 min then stop. During this time it would be really loud. Turns out to be a bad Motor. To replace 1) Removed bottom kick panel by removing 2 screws. 2) Then removed upper front cover by 2 additional screws. 3) Disconnected thermostat (marking location of wires on paper). 4) Removed blower housing (3 screws)undid the rib belt from the drum by pushing the pulley wheel up so the belt could be loosened and removed from motor. 5)Removed the front cover of the dryer opening by removing 2 screws. 6) Lifted up and then puled it out to expose the drum. 7) Removed the drum w/belt from the dryer exposing the motor. 8) Removed 2 screws from the motor and disconnected the plug from it. Slid it all the way out. 9) Need to remove (3 screws) the metal faceplate from motor to access the blower wheel (plastic). 10) Unscrewed the plastic wheel and removed 2 screws to remove the motor from the frame. reversed the process for reassembly. Sounds tougher than it really was - only took 30-45 min. Suggestion - write down on paper location of any wires you disconnect - makes reassembly very easy. Also recommend vacuuming any lint in the dryer while it is completely accessible.

Help other customers find the most helpful instructions.

Were these instructions helpful?