2039613-1-S-Whirlpool-37001298-Drum Glide
2039613-1-S-Whirlpool-37001298-Drum Glide 2039613-2-S-Whirlpool-37001298-Drum Glide

Drum Glide

PartSelect Number PS2039613

This drum glide is sold individually. ***Please Note: these should be replaced in pairs.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Marks left on clothes.
  • Compare At

    $4.69
  • You Save

    $.78
  • Your Price

    $3.91
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Single Felt Pad

Part Number 2045752

$3.91
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 43 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Socket set

CustomerBruce from Frazer PA

Loud squealing noise

Loud squealing noise coming from the idler pulley. The pulley was not spinning freely on the shaft of the idler pulley lever to the point of putting a groove in the pulley and damaging the belt. To fix the problem replaced the belt, idler pulley, and idler pulley lever. Because I had the dryer apart also replace the following items. Drum support roller and drum slides.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerTodd from Red Lake MN

Dryer was making a grinding sound

I opened new parts and stcuk a felt pad on each glider and put one of my 10 lb. weights on it for about 1/2 hour to help it stay in place.

Then removed top panel and then the front..There are three phillips screws that hold the lint catcher in place inside the barrell. Then remove the 4 total bolts to remove Glide Brackets.

Mine was so worn down that the barrel had rubbed alomost all the way through a bracket.
Once felt pad was firmly set, i attached glider into bracket and installed them.

Put everything back in place and started up..and it was running and sounding like new...i paid 27.00 for parts and saved big time compared to what a service shop would have charged me.

The shipping was super fast and with my wife and i having 9 children in the house it was a life saver for us.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerGregory from Virginia Beach VA

Noisy belt/slipping intermittantly

Unplug Dryer. Remove lower and upper front panels [remove wires from upper right door switch]. Lift up on belt idle pulley and take belt off pulley/motor.Remove Front Bulkhead and dryer lint/vent ducting. Note position on drum and remove belt. Unbolt top panel front 2 screws to allow room to remove drum.Remove drum. Take lock rings off Drum support rollers and remove old rollers. Clean roller shafts and apply hi-temp grease [I used ultra hi temp brake grease-ceramic based-small packet can be purchase fm auto parts store]. Re-install new support rollers and lock rings. Re-install drum and slide belt back into position. Remove and replace felt pads and glides into inside of Front Bulkhead. Reinstall Front Bulkhead and top panel [connect door switch wires].Install belt around idle tension pulley. Re-install lower panel.All parts fit perfectly and delivered quickly.Belt had just been replaced previously.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Socket set, Wrench set

CustomerRichard L from Eatonton GA

Glides were wore out and pully was gone.

Replaced glides and assy idler pulley cleaned all parts fron dust and debree, vaciumed heating eliment to remove all excess lint and wool to make sure I did'nt have a fire in the lower unit.
Job was'nt all that hard just have to watch what you're doing.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerJack from Nashwauk MN

Felt seal was shredded and glide bracket was worn through

The on-line video showed the dryer top being loosened from the front as the first step. On our dryer, the bottom panel in the front needed to be removed first - two screws, then the front panel(with door)- two more screws and two wires for the switch. Next was the front guide panel - four screws. The glide brackets bolted to this panel and the felt seal was glued to it. Reverse the process to put it all together, and my wife was happy again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Drum Glide

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

Customerdave from sparta MI

Drum glide worn out

i watched the video that you provided and the repair went just as show. the video was a great to have.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerLarry from Lima OH

Belt was worn - ready to break, decided to replace the parts that commonly go bad.

I removed the bottom panel, then the larger front panel that includes the door. After that, removed the top 2 screws so that the top would swing up (but not lift off). After that, I removed the front "bulkhead", and the drum. Then it was just a short matter of sweeping everything out, and replacing the parts one by one. Most came off with a socket, or snap ring pliers. Pretty obvious at this point...

Be sure to label any wires - I removed 5 wires all total, and wrote down the colors and where they went.

It's great to have help when working with the drum. BTW, you CAN replace the belt without taking out the drum, but you better have strong fingers to move the belt tensioner and slip the belt on it - all with one hand. I did it, but that was the least "fun" part....

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsWrench set

CustomerBill from Milford NH

Idler pully wheele and belt worn. Wheele flat on one side.

Downloaded an Amana service manual and followed directions. Easy...and was able to clean out built up lint not to mention a couple of dollars in change!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerGregory from Odessa MO

Drum made a lot of noise and the drum turned hard

Removed top and front panels, reached in by motor and removed belt from motor, removed drum and replaced slids and back drum wheels. re-assembled the front and top.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerKurtis from Liberty Township OH

Worn drum roller - squealing

Removed front panels and swiveled lid upwards. Loosened tensioner, removing belt and then carefully extracting the drum. Replaced 2 drum glides on underside of front panel. Next 2 rollers, which appear to unscrew, but do not do so. You must remove the retaining ring (surprise! ...and 2 screw drivers later). This was the longest and most frustrating part of the whole ordeal. Then just reverse the process for reassembly. This was my first electric dryer repair and it really wasn't too bad. Online docs I found were somewhat helpful, but really luck and perseverance. I did save probably $300 in replacement costs, which is quite satisfying. .

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDoug from Corning AR

The brackets that support the front side of the tub were worn out and one of them was worn in two

I started at the bottom and removed the two nut screws that support the bottom section of the front of the dryer. Then I removed the two nut screws that supports the next section and disconnected the two wires ( making note of wich terminals each wire went to). Then I removed the lint trap housing( three phillips head screws hold it in place from the inside). Next ,I removed the face plate( held in place by 4 nut screws and two metal tabs at the bottom). Then I took the old tub brackets and felt seal off of the face plate . Next ,spray adheisive arond the ring of the face plate and install the new felt seal, then the new brackets and dryer glides and felt pads. Last, re-install all components.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)

CustomerMike from San Clemente CA

Worn out bushing in support roller, dryer glides and felt disinigrated. Worn out felt cylinder seal

Unscrew front, detach electrical, tilt back top, remove drum. remove retaining ring and glide, replace ring and guide remove old felt seal, adhere new felt seal with contact cement, remove what was left of felt pads, replace pads and new glides, reassemble.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerHugh from Lansing MI

Dryer had an intermittent squeak

1st of all my dryer came apart differently than your video showed. I had to remove the lower front panel (2 5/16 screws) then remove the upper front panel (2 5/16 screws)and the spring clips mentioned in the video, then the top with two more screws. After that the removal of the front drum support assembly was as shown in the video. I then loosened the drive belt, removed the drum and the external grip ring securing the idler pulley. The pulley rotated very hard since the shaft and bearing were partially seized. I cleaned the shaft before installing the new pulley. When I initially took the dryer apart to see what the problem was I noticed the front drum guides were showing wear so I ordered and replaced them and the felt pads just to prevent problems in the near future.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set

CustomerLarry from Bend OR

Roller wheels worn out

Super Simple. Remove lower front panel (2 screws). Remove front door & panel (2 more screws). Disconnect push on wire connectors after marking each side with a sharpie pen (for easy re-assembly). Top hinges up towards the rear and rests against the wall. Lift out the drum. Remove snap rings on the shaft that holds the guide wheels at the rear of the drum. remove wheels. One of the shaft pieces that holds the wheel was shot so I replaced that (2 screws). Put new wheels back on. This was actually fairly hard. the new shaft seemed to have a larger receiving end. with hammer and lube I eventually got it on. Re-assemble in reverse order. took about 20 minutes. the only special tool was snap ring pliers (could easily get snap rings off with a flat screw driver.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)

CustomerJohn from Ruther Glen VA

Loud rubbing sound that got louder as dryer was used.

Removed dryer vent and gas line. Turned off gas first. Removed front of dryer. Removed door to get to drum support. Removed drum and belt. Removed and replaced rear drum rollers. Removed and replaced front drum supports. Idler wheel was removed and replaced. Cleaned inside of unit and reinstalled the drum and belt.Reinstalled all of pieces removed. Reconnected power and started dryer. Sounded like a new dryer. Reconnected gas and put unit back in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?