2039604-1-S-Whirlpool-37001287-Idler Lever
2039604-1-S-Whirlpool-37001287-Idler Lever 2039604-2-S-Whirlpool-37001287-Idler Lever 2039604-3-S-Whirlpool-37001287-Idler Lever http://www.partselect.com/Schematics/Maytag/58908.gif

Idler Lever

PartSelect Number PS2039604

The spring for this part is sold separately.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Will not tumble.
  • Compare At

    $20.54
  • You Save

    $3.42
  • Your Price

    $17.12
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Idler Pulley Spring

Part Number 2052983

This metal spring fits onto the arm of the idler pulley assembly.

$20.77
Special Order

Idler Pulley Wheel with Bearing

Part Number 2200898

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$8.31
On Order

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.0 / 5.0, 34 reviews What's this?
31-34 of 34
 

0 of 1 people found this instruction helpful

Parts Used:
  • Idler Lever
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: steve from elizabeth, PA

Noise

remove front door,disconnect plug from motor remove motor assy,replace idler

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Customer: Anthony from Rochester, NY

Dryer would vibrate and make a loud bad bearing sound.

I began by disassembling the dryer to diagnose the problem. I discovered the belt had been riding on a section of a broken idler pulley as well as wearing a groove into the idler pulley bracket. I removed the broken parts and went to the Internet for replacement parts. Three days later the parts arrived and I began reassembly. I found it a little difficult to replace the drum with the belt in position but found it much easier to recruit some assistance during this phase. Another factor with the difficulty was that I hadn't paid real close attention to the webbing direction of the belt around the pulley and there were no diagrams depicting the proper direction of the new belt. I did figure it out relatively quickly but would advise paying very close attention to parts positioning during disassembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used:
  • Idler Lever
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench set
Customer: Av from La Habra, CA

Dryer broken belt and wear out tension roller

Easy to fix as long you look online how to fix dryer amana may tag

Help other customers find the most helpful instructions.

Were these instructions helpful?

44 of 1297 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Socket set, Wrench set
Customer: russell from anamosa, IA

Would run but would not heat

removed front cover and top took drum out remove heating unit replced limit switch and fuse reinstalled installed new idler put new belt around drum installed drum replaced glides put top back on and front cover . then replaced boosting heater witch is on the blower also cycling thermostat

Help other customers find the most helpful instructions.

Were these instructions helpful?

31-34 of 34