2039485-1-M-Whirlpool-37001132-Cylinder-Felt-Seal.jpg
2039485-1-S-Whirlpool-37001132-Cylinder-Felt-Seal.jpg

Cylinder Felt Seal

PartSelect Number PS2039485

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Marks left on clothes.
  • Takes too long to dry.
  • Will not tumble.
  • Compare At

    $19.93
  • You Save

    $3.32
  • Your Price

    $16.61
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

High Temperature Adhesive - 2oz.

Part Number 2196040

$12.33
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 19 reviews What's this?
16-19 of 19
 

1 of 6 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set

CustomerVan from Richardson TX

Loud squeaking, and long drying time

First: I read a lot of repair stories on PartSelect.com, as well as on other sites.
Removed 2 screws and took off lower panel. I turned the drum by hand, and identified the left/rear roller to be the squeaking part. Removed the 2 screws that held the door panel, removed it, and enjoyed the fireworks!!!, because I had neglected to unplug the dryer first. The door switch was ruined, but I was thankful that no bodily injury or severe property damage happened.
While I was shining the flashlight toward the back/underside of the dryer, my dear wife noticed light inside the drum.
Ordered a new new door switch, roller axle, roller and rear felt cylnder seal...all arrived in 3 days.
Decided to replace the front felt seal too, and bought it at a local shop, along with the adhesive, which I couldn't find at PartSelect.com for less than $32.
Took the front drum panel, belt, drum and bulkhead panels off per advice at this site.
Replaced switch, but had to crimp on a new spade connector (included with the switch).
Cleaned off old felt seal adhesive with Goof-Off, and glued on the new seals.
Replaced the real axle and wheel, with a little added lithium grease.
Cleaned out the dirt in the dryer cabinet, and put everything back together with my wife's help and her keen common sense.
The dryer is much quieter, and dries faster thanks to the new seals.
The repair was straightforward, but I rated it "a bit difficult" because of the amount of taking-apart and rebuilding that I decided to do.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 379 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Socket set

Customerchristopher from sycamore IL

Dryer banging and clothes getting stuck between tub and felt pad while tumbling.

Very easy repair. I took off the bottom fromt panel with a nut driver. Then I took off the face/door panel. Take note of the wires that need to come off by marking them with a sharpie or tape. The top of the dryer can be stood up to allow access to the ductwork that has the felt pad on it. The felt pad was worn through in spots, the drum glide was completely gone and both cylinder glide brackets were almost completely worn through. I just replaced the brackets and the pads. The old felt came off fairly easily. I scraped the old glue for the felt off with a knife and cleaned and dried the surface before applying the hi temp adhesive. I waited 1 minute while the glue became tacky (be careful, the glue starts out thin and tends to run) and the felt pad was easily put back in place with my wife's help. Everything was very simple and it cost $87.00 for parts and shipping. I felt that this should be a good investment since I have had no other problems with this dryer and this is normal wear and tear. Better than paying $600+ for a new dryer. The video for changing the felt pad was very detailed and easy to follow as well.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 500 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerChad from Caldwell ID

Dryer made marks, then noise, then more noise

Thanks to this website we were able to not only find the parts, but a video that told us how to take the dryer apart. Unfortunately, between the time we diagnosed the problem, ordered the parts, and they arrived, the drum had worn into the front bulkhead. We were able to file the sharp parts dull and install the brackets, felt pads, and drum glides along with the felt seal, but ended up breaking the dryer door switch. Once that came in, it has been working. I'm not sure how long the repair will last, but it was much better than buying a new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 644 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

Customerjoe from johnsburg IL

Lots of noises

disassembled found bunch of worn out parts . I went to website wich was very helpful found all . my worn out parts online. dryer is very quiet now I wish i would have done it sooner.P.S. going to fix my dads dryer next. thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-19 of 19