2037923-1-S-Whirlpool-35-2045-Lid Hinge Pin
2037923-1-S-Whirlpool-35-2045-Lid Hinge Pin 2037923-2-S-Whirlpool-35-2045-Lid Hinge Pin

Lid Hinge Pin

PartSelect Number PS2037923

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Lid or door will not open.
  • Lid or door won’t close.
  • Compare At

    $8.95
  • You Save

    $1.49
  • Your Price

    $7.46
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Lid Hinge

Part Number 2037922

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.

$4.05
In Stock

Screw

Part Number 2026498

This screw is a metallic screw that is used for many clothes washers.

$2.70
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 39 reviews What's this?
31-39 of 39
 

0 of 1 people found this instruction helpful

Parts Used

  • Lid Hinge Pin

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerThomas from Lakewood CO

Broken hinge

Removed the screws and lid. Cleaned up lid and parts. Had to sand down pin as to tight on lid. Easy job.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerTish from Albuquerque NM

Lid hinge pin broke in half

Easy to remove broken part. Found rust, so after cleaning I applied paint (I let dry overnight).

By manipulating the washer drum, moving left and right, the screws were easy to get to. However, to get the screws back in took tightening by strong hands. Plus, found that the lid sensor had worn out, so that was adjusted.

New screws would probably make the job easier.

All is fantastic and I found it was "easy" to replace with finishing help from strong hands.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set, Wrench set

CustomerDennis from Oshkosh WI

Lid to wash tub was completely broken off (bought it that way - got it cheap because of this).

Remove two screws holding a special clip on the back of the washing machine (near top- one on each side). Top of washing machine pops off now by prying front edge up (2 snap type clips hold front edge of top down). Once top is loose just pivot it up on edge so you can get to the bottom side of it (don't have to remove the wires etc. as they are long enough for this). Remove one screw in each hinge half located on bottom side of washing machine top and remove old hinge half from top. Remove broken hinge halves from door to washing machine by removing one screw from each one. Put new hinge halves together and fasten to door. Then set entire hinge/door assembly on washing machine top and screw to top as an assembly. Snap top of washing machine back down on front of machine and put clips/screws back in on back of machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerPatricia from South Amboy NJ

Hinge assembly snapped off after years of use.

I had my son remove all of the old hardware with an allen-key wrench. He then proceeded to install the new hardware. Fisrt he installed the pins on the lid. Next, he installed the hinges to the washer, leaving each hinge loose. Finally adjusting the lid until the screws for the hinges were completely tightened.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Lid Hinge Pin

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

Customernancy from hilliard OH

Door hinge broke

Remove door, then after purchase of special screw driver was able to remove the broken plastic hinge. Replace with new hinge. A bit of a challenge due to screw under the lid. Finally, it's fixed for a whole lot less than a service call would have been.

Part Select was efficient & quick at sending us the part needed to complete the task. I will recommend this web site.

Thanx again

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJan from Challis ID

Lid hinges wear out, causing lid to slam as you are trying to put clothes in or take them out.

Lift the top of the washer so you can access the screws that hold the hinges. Replace the hinges,and close the washer top. This is the sescond time we have had to replace the hinges.

This lid and hinges are very poorly designed. Instead of opening to the side, it opens straight back. That means when the hinges wear out (and they do because they are plastic), you have to push the lid all the way back to stay open. When you push it all the way back, it hits the control knob and turns off the water.

If you are like me, I like to turn the water on and add the soap so it can dissolve before I add the clothes. It is really irritating when you open the lid and the only way for it to stay open is to push it all the way back and the water shuts off. And if you don't push it all the way back, it slams and scares the bejeebers out of you or slams on your fingers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRichard from Vandling PA

Hinge pin broke

push the washer tub as far as you can and use a long screwdriver to take hinge off,do the same for other side. Lid will then be removed for access to hinge pin,remove hinge pin and reverse process. Very easy repair. Very fast delivery from PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerEugene from La Junta CO

One hinge pin broke on the lid.

1. Open washer lid.
2. Remove right hinge mounting screw by leaning agitator/tub assembly to the right.
Do the opposite for the left hinge mounting screw.
3. Remove and replace both hinge pins on the lid.
4. Install both hinges on the pins and install lid back on the washer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerjack from Hillside NJ

The hinge pin broke off on the washing machine lid

Just popped open the top of the washer, took the broken hinge off and replaced it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

31-39 of 39