Water Inlet Valve

PartSelect Number PS2037785

This valve has two ports for water to enter. This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not fill with water.
  • No hot or cold water.
  • Will not stop filling with water.
  • Leaking.
  • Compare At

    $73.56
  • You Save

    $12.26
  • Your Price

    $61.30
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 6 reviews What's this?
1-6 of 6
 

7 of 9 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Wrench(Adjustable)

CustomerNicholas from Parrish FL

Weak cold water flow

First I thought hoses could have been clog, turned out that the flow valve was bad
One screw to take off the value holder itself, removed the two hoses that bring hot and cold water to the valve, removed the water line that brings the cold and hot water to the washer (nothing more than a hose clamp) Was then able to remove the valve holder. Simply unbolted the value from the holder, replaced with new valve and reversed processed to re-install.
Pretty easy, about minutes

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerGeorge from Grove City PA

The washer was taking a long time to fill and would run through multiple cycles

Removed old timer replaced new.
Removed old water inlet and replace with new. I don't think that the water inlet valve had anything wrong with it. But I had one go on me before and thought that It may be the cause of the filling problem. We thought it was taking forever to fill, when actually it was just running through all of the cycles.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerNick from Oceanside CA

A small leak into the tub

1. Removed the hot and cold water hoses. 2. Undid one screw holding on the solenoid mounting plate. 3. Pushed the plate in at the top to unlatch the plate at the bottom. 4. Pulled the plate out and undid the output hose. 5. Replaced the solenoid assembly held on by two screws. 6. Replaced it all in the revers order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)

CustomerDennis from Bandera TX

Water continue to drip with machine shut off

Rear panel has to be removed to access part. Removing controls top of machine, two screws lower left and right, will make back panel removal easier. Back panel hangs on 2brackets,protruding thru the panel, near the top, and 3 screws across the bottem. You will also have to remove the drain pass thru connecting the internal drain hose to the external drain hose. The replacement part does not have matching screw mount holes to those on the rear panel. Their is a square punch out with a tab on the replacement which can be used for the top mount screw. Use a drill and bit to round the hole. Mount replacement then drill a hole in the replacement for the the lower mount screw. 1 day service and works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerStacey A from Richmond VA

The cold water was barely filling the tub of the washer

First I removed 2 screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I connected the new value and put it back in place. I then put the screws back in place.

This was very easy and it solved my problem

Thanks a lot

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerLeonard from Glen Allen VA

Slow fill on cold cycles.

The repair was easy. It took approximately 30 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6