2035729-1-S-Whirlpool-33001932-Timer
2035729-1-S-Whirlpool-33001932-Timer 2035729-2-S-Whirlpool-33001932-Timer 2035729-3-S-Whirlpool-33001932-Timer http://www.partselect.com/Schematics/Maytag/53128.gif

Timer

PartSelect Number PS2035729

This part comes with the chiming mechanism. It runs at 1/3 horse power.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not shut off.
  • No heat or not enough heat.
  • Compare At

    $149.52
  • You Save

    $24.92
  • Your Price

    $124.60
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 7 reviews What's this?
1-5 of 7
 

13 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Jerry from Las Vegas, NV

Timer assembly would not advance

Removed old timer assembly, put the new one next to it and as I disconnected one wire from the old part, I connected it to the new part, that way I was able to connect each wire to the right place.
It was very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used:
  • Timer
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers, Wrench set
Customer: Richard from Keswick, VA

Dryer timer dial was cracked and thus would not turn the timer pivot.

Ordered the three pieces of the dryer dial and replaced the old dial with the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used:
  • Timer
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Randall from Viper, KY

Dry er would run but no heat.

Appliance dealer stated that usually timers did not go out and thermostats were most likely . Tried all and called repairman that did not show. Removed cover found burned gear in timer ordered. The part is easy to replace just change wires one at a time or take a digital pic of the wires.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver
Customer: Robert from Ray, ND

The dryer would not shut off. The timer would not advance,

I replaced the timer and timer dial skirt which was very easy to repair. The dryer would not shut off and the timer would not advance. I could manually use a plier to move the timer and it would shut off then. I replaced the timer and it works well now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used:
  • Timer
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Walter from Flagstaff, AZ

Timer quit working after lighting strike

remove back cover 3 screws, change wires in same order as old timer, remove two mounting screws under timer dial, check voltage-replace temp sending control attached to brown wire.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 7