2035633-1-S-Whirlpool-33001809-Moisture Sensor
2035633-1-S-Whirlpool-33001809-Moisture Sensor 2035633-2-S-Whirlpool-33001809-Moisture Sensor

Moisture Sensor

PartSelect Number PS2035633

This part helps determines the dryness of the clothes to reduce over-drying.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Shuts off too soon on auto dry.
  • Takes too long to dry.
  • No heat or not enough heat.
  • Will not shut off.
  • Compare At

    $21.80
  • You Save

    $3.63
  • Your Price

    $18.17
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 7 reviews What's this?
1-7 of 7
 

16 of 21 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerRaymond from Marlton NJ

Dryer not staying hot. Heat shuts off and doesn't come back on.

Detach front door and pop off front panel. Replaced heating unit on right and all parts on unit. Replaced cycling timer and thermostor on left. The thermostat was the last item replaced. We did this on three stages. First we replaced heating element, still had problem. Then we replaced the high limit and cycling thermostats, still had problem. Had a repairman out. He could not figure it out, because there were no error codes. He suggested replacing the thermostor. We did that and it fixed our problem. We could have saved alot if we did that first, but no one mentioned that part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 15 people found this instruction helpful

Parts Used

  • Moisture Sensor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerDavid from Preston CT

The moister sensor broke away from it's two fasteners inside the dryer drum.

Unscrewed the two fasteners, rerouted one wire using a wire coat hanger, plugged in the new moisture sensor to the two wires and fastened the the sensor in place using the two existing screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 10 people found this instruction helpful

Parts Used

  • Moisture Sensor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerPaul from Tamaqua PA

Dryer shut off before clothes were dry

The old sensor came out by removing 2 screws. I unplugged the two wires from the back of the sensor and plugged them into the new sensor. I reinstalled the new sensor using the same two screws. Of course, I unplugged the dryer first.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 11 people found this instruction helpful

Parts Used

  • Moisture Sensor

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

Customerkeith from saluda VA

Dryer continuously running, no timer advance, dampness indication stayed on "wet"

Took 3 screws out of the back of the back of the machine and tilted the control panel houseing forward. Slid the module free of it's track and unplugged the bundled wiring plug. Plugged new module, relpaced in is slot and put the control panel back in place

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerRobert from Bulverde TX

Baffle became loose and sensor stop working

Repair is very simple, all I had to due was remove 4 screws on door and closing side door. Remove door and take off front panel. Then I spun baffle down to right side by motor removing 2 screws , replaced short baffle. the sensor wires are locate right there . Simple disconect of 2 spade wires , 2 srews inside and unit comes out. Please remember to disconnect power and door lifts up maybe 1/2 inch when disconnecting. The baffle worked fine the sensor fixed lights , but did not dry clothes to my satifaction. Good Luck

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Wrench(Adjustable)

CustomerLawrence S from Rancho Santa Margarita CA

After initial ignition & first heat cycle, gas valve would fail to re-ignite

The good: No need to pull out dryer beyond point where (wall) gas valve could be shut off.
The gotcha: Be sure to wear thick leather gloves to protect your hands. I discovered sharp edges the hard way!
The tip: To loosen gas valve inlet nut and to remove gas pipe from valve, use a bottom-to-top wrench motion. Despite threads being right-handed, this counter-intuitive operation (the thinking is that you are tightening the nut instead of loosening it) is necessary due to nut being located on the valve rather than the gas pipe which reverses the context.
The ending: Wife is happy to be back in the drying business and I'm happy just to have her happy not to mention saving a little $ in the process! Thanks PartSelect.com!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 13 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Socket set, Wrench(Adjustable)

CustomerBen from Licking MO

Loud scraping sound

i removed the front cover .then i removed the two screws thet held the top and then raised it up then silde out the drum. replaced the rollersthat the drum runs on. then just put it back together. not a hard job at all.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-7 of 7