2035614-1-S-Whirlpool-33001790-Blower Wheel
2035614-1-S-Whirlpool-33001790-Blower Wheel 2035614-2-S-Whirlpool-33001790-Blower Wheel 2035614-3-S-Whirlpool-33001790-Blower Wheel http://www.partselect.com/Schematics/Maytag/LD14-40.gif

Blower Wheel

PartSelect Number PS2035614

This blower wheel does not come with a spring clamp, but it does have twenty fins and it is designed to fit a 3/8 of an inch motor shaft.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Compare At

    $26.32
  • You Save

    $4.39
  • Your Price

    $21.93
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 4 reviews What's this?
1-4 of 4
 

10 of 13 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers
Customer: Terry from Caruthersville, MO

Loud noise inside dryer

After changing all the rollers in the dryer (which didn't fix the problem) I decided to take apart the blower. Sure enough, that was the problem. As the dryer heated up, the damaged wheel would swell and start rubbing the housing. I replaced both and fixed the problem. The repair was pretty easy, since I had taken the dryer apart several times replacing the rollers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Carol from Onsted, MI

Blower wheel over time became clogged w/lint & caused the dryer to vibrate

Removed the dryer front, then detached the retainer ring holding the blower wheel in place. Set the new blower wheel, attached the new ring retainer and placed the dryer front back in place. Thank you for the low prices - I searched on-line at 3 sites and you were the best price available.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Robert from Lebanon, PA

Blower wheel had broken fins, motor bearings loose

This was fun! Kill the power!
Remove door, remove from panel, remove front drum support, remove drum and belt, remove blower cover, remove blower wheel, remove electrical connector from motor, take two clips off motor mount to remove motor. Put it all back in with new parts. 200 bucks and back in business. Go for it.
Bob

Help other customers find the most helpful instructions.

Were these instructions helpful?

22 of 651 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Mary Beth from Lake St. Louis, MO

Blower wheel broke

Replaced bower wheel, drum rollers,belt and Idler pulley while the dryer was apart. so far so good. Easy repair
Motor bearings seemed tight so hopefully will get another ten years out of dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4