BBB A-Plus
2035614-1-M-Whirlpool-33001790-Blower-Wheel.jpg
2035614-1-S-Whirlpool-33001790-Blower-Wheel.jpg 2035614-2-S-Whirlpool-33001790-Blower-Wheel.jpg 2035614-3-S-Whirlpool-33001790-Blower-Wheel.jpg

Blower Wheel

PartSelect Number PS2035614

This blower wheel does not come with a spring clamp, but it does have twenty fins and it is designed to fit a 3/8 of an inch motor shaft.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise
In Stock

  • Compare At

    $36.71

  • You Save

    $6.12

  • Your Price

    $30.59
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 NEXT > 1-4 of 4

 

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerCarol from Onsted MI

Blower wheel over time became clogged w/lint & caused the dryer to vibrate

Removed the dryer front, then detached the retainer ring holding the blower wheel in place. Set the new blower wheel, attached the new ring retainer and placed the dryer front back in place. Thank you for the low prices - I searched on-line at 3 sites and you were the best price available.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerTerry from Caruthersville MO

Loud noise inside dryer

After changing all the rollers in the dryer (which didn't fix the problem) I decided to take apart the blower. Sure enough, that was the problem. As the dryer heated up, the damaged wheel would swell and start rubbing the housing. I replaced both and fixed the problem. The repair was pretty easy, since I had taken the dryer apart several times replacing the rollers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRobert from Lebanon PA

Blower wheel had broken fins, motor bearings loose

This was fun! Kill the power!
Remove door, remove from panel, remove front drum support, remove drum and belt, remove blower cover, remove blower wheel, remove electrical connector from motor, take two clips off motor mount to remove motor. Put it all back in with new parts. 200 bucks and back in business. Go for it.
Bob

Help other customers find the most helpful instructions.

Were these instructions helpful?

20 of 647 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerMary Beth from Lake St. Louis MO

Blower wheel broke

Replaced bower wheel, drum rollers,belt and Idler pulley while the dryer was apart. so far so good. Easy repair
Motor bearings seemed tight so hopefully will get another ten years out of dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 NEXT > 1-4 of 4