2035582-1-S-Whirlpool-33001755-Short Baffle
2035582-1-S-Whirlpool-33001755-Short Baffle 2035582-2-S-Whirlpool-33001755-Short Baffle

Short Baffle

PartSelect Number PS2035582

This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Unusual Noise.
  • Will not tumble.
  • Takes too long to dry.
  • Compare At

    $25.45
  • You Save

    $4.24
  • Your Price

    $21.21
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Tall Baffle

Part Number 2035811

This part moves the clothes around inside your dryer and helps to direct the flow of hot air during the drying cycle.

$19.47
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 20 reviews What's this?
16-20 of 20
 

0 of 1 people found this instruction helpful

Parts Used

  • Short Baffle

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench set

CustomerCheryl from Bellevue NE

Short baffle broke off in the dryer

Removed the door and the front panel by removing the screws in the door hinge and two more screws opposite the door. Then removed two screws at the top of the front of the dryer, one on each side. The allowed a bracket that held down the top of the dryer to be removed. Then I lifted up the top of the dryer and propped it open with a small box. Then all that remained was to put the new baffle in the inside of the dryer drum and replace the screws from the outside of the dryer drum. My only complaint was that the new baffle did not come with two new screws. I had to go out and buy them separately because I only found one of the old screws in the bottom of the dryer under the drum.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Socket set

CustomerPhil Lind from LOUISVILLE CO

Baffles,( 2 out of 3) cracked and fell off dryer tumbler

Fairly straight foward repair 1. unplug power 2.remove dyer door.3. remove clips top side they hold the top 4.lay top over and front panel cover will also lay flat 5.install baffles(you"ll ned to roll the tumbler over by hand).6. most important! vacuum out lint and debris including the vent hose &.reverse the 5 steps and viola

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerAl from Newark DE

Dryer baffle broke off and rear felt seal was pulled out

1. Remove 2 screws that hold door hinges on.
2. Remove 2 screws on opposite side of door hinge and remove 2 plastic clips.
3. There are 2 hex screws that hold the front panel on. Remove these and the panel is held on by a flex clip. Gently twist the top towards the outside of the dryer and they will come free.
4. tilt panel forward and lift of 2 clips at the bottom.
5. Remove the screws under the cover panel which will release the drum holder and lint collector.
6. Lift top of dryer and lift out drum.
TAKE THE TIME SINCE THE UNIT IS OPEN TO VACUUM OUT THE ENTIRE DRYER. CLEAN OUT THE EXAUST TO IMPROVE EFFICIENCY AND SAFETY.
7. I replaced the rear felt by using a flat head screwdriver to lift tabs and install felt. Using the screwdrive I compressed the tabs to hold the felt.
8. The baffle was installed inside the drum and using 2 hex bolts to hold the baffle in. I added 2 washers since the hole was inlarged due to the baffle becoming loose and pulling through the metal drum.
9. Re-install the drum and push rear felt to the outside of the drum.
10. The front drum needs to be installed. Push the felt to the outside of the drum and check the rear felt to ensure it is still on the outsid of the drum. Install 4 hex screws to secure front drum holder.
11. Insatall lint catch unit with 4 additional hex screws.
12. Verify the lint collection panel lins up with the exhaust fan at the base. When units line up tighten all 8 hex screws.
13. Reinstall front cover panel by inserting panel on bottom clips and tilt up to the dryer. The top corners are gently twisted to the outside of the dryer to reattach to the spring clips. Use 2 hex screws to attach panel.
14. Re-attach plastic clips and 2 screws on side opposite of door hinges.
15. Re-attach door hinges with 2 screws. Cleck to ensure the door closes.
16. Check dryer operation.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Short Baffle

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Wrench set

CustomerAlice from Pottstown PA

Baffle fell off

Baffle replacement did not include screws. Replacements were hard to find. The missing ones were not accessible in the bottom of the machine (behind motor,etc). Also screw holes were not predrilled so difficult to attach with limited space.

The best was a Utube video by someone who had an arm in a sling, therefore a one-armed installation. It was excellent instruction.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerNathan from Brookfield WI

Baffles broke off

Unplugged dryer. Removed dryer door with philips screwdriver. Removed front dryer panel aftr loosening philips screws on each side of door. Then at top right corners I used a nutdriver to remove clips/hooks that hold down top of dryer. I then lifted top of dryer up- it is hinged at back. I could then manually turn drum to access screws that hold baffles. I held each baffle in place with left hand and turned in screws with right hand until tight, using nut driver. I vacuumed out inside of dryer. Reassembled top, front panels and door. plugged in and tested. All good.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-20 of 20