Timer

PartSelect Number PS2035560

This timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not shut off.
  • Timer will not advance.
  • No heat or not enough heat.
  • Compare At

    $119.26
  • You Save

    $19.88
  • Your Price

    $99.38
In Stock
Order within the next 11 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 4 reviews What's this?
1-4 of 4
 

10 of 14 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers, Screw drivers

Customergeorge from camden SC

The dryer would not cool down in the permenant press cycle or any other cycle.

Pull the electric plug. With a nut driver and phillips screw driver remove two bolts and three screws on the rear access plate. Gently pull the knob from the front pannel and with the nut driver remove the two bolts under the knob. The timer is now loose from the drver. Match the wire plug codes on the old and new timers. Remove one wire at a time from the old timer with pliers and plug it onto the new timer on the same coded pin. Slide the timer back into the pannel and replace the two bolts that hold it. Replace the knob. Replace the three screws and two bolts holding the back pannel. Plug the electric cord back into the wall socket.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 7 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRichard from Long Valley NJ

Heater stop working!

Checked all other electrical and mechanical operations and all seemed operational. Removed heating element from unit and checked with VOM. It was OK. Reinstalled and began checking wiring with VOM per the diagram in the control panel cover. Determined that the contacts for the heater in the timer unit had failed. (Open) Temporarily shorted these points on the timer with a strap to make the dryer work. Wife is now happy. Two days later when the timer part arrived, installed and now all is operational. Good for another 10 years.
Dick

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMary from Memphis TN

Dryer would not heat

My husband did the repair - first appliance repair he has done in 37 years of marriage and it was EASY!!!! Ordering was a breeze - part arrived more quickly than appliance repair company could provide it. Saved over $100 ordering from this site and doing ourselves. Directions provided from site were spot on perfect!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 4 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSTANLEY from PLYMOUTH MA

Would not start at times intermitant on off

called electrian breaker had a slight burn spot on the contact. I was very impressed by your company getting the parts to me so quickly. I'm sorry that I have to return them because the repair would have been much cheaper. Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4