2034121-1-S-Whirlpool-31940001-Flat Style Oven Igniter
2034121-1-S-Whirlpool-31940001-Flat Style Oven Igniter 2034121-2-S-Whirlpool-31940001-Flat Style Oven Igniter 2034121-3-S-Whirlpool-31940001-Flat Style Oven Igniter http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/32589.gif

Flat Style Oven Igniter

PartSelect Number PS2034121

This part has a ceramic housing and comes with a connector. NOTE: This part may look different than the original, but will function the same.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Gas igniter glows, but will not light.
  • Little to no heat when baking.
  • Will Not Start.
  • Compare At

    $54.92
  • You Save

    $9.15
  • Your Price

    $45.77
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 78 reviews What's this?
1-5 of 78
 

52 of 62 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver

Customermark from macomb, MI

Oven not working but broiler was working fine.

Checked lower oven burner for a problem. Oven Ignitor looked like it was glowing and working properly but the gas valve would not open to let the gas flow to burner. I had read on a forum that just because the oven ignitor looks good does not mean it is creating the proper resistance to open the gas valve. So I took my chances and replaced the ignitor (because it was cheaper than the gas valve) and now the oven works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

24 of 26 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsSocket set

CustomerDavid from Avon, IN

Igniter glows, oven won't light

I removed the cover over the flame diffuser, then removed the single nut holding the diffuser to the burner assembly. After removing the three screws from the igniter assembly I found I couldn't reach the connector for the igniter.
I removed the storage tray underneath and found a cover towards the rear of the oven with two screws. After removing this piece I could easily disconnect the igniter. It was a bit difficult replacing this shield as it had to fit between two other pieces on the side towards the front of the oven.
I slid the guard from the old igniter and put it on the new piece and just reversed the procedure. Relatively easy and saved me a bundle!

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 18 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers

CustomerMark from Munroe Falls, OH

The amana oven & broiler igniters failed after 7+ years of service

Broiler Igniter:

Disconnected stove from electricity

Removed the two screws that hold the broiler igniter assembly

Pulled asembly out to expose ceramic wire nuts

Removed ceramic wire nuts and save them

Removed broiler igniter assembly (broiler igniter & brolier mounting bracket are assembled together)

Loosened screws/nuts that hold the broiler igniter to the brolier mounting bracket

Remove old broiler igniter

Carefully inserted new brolier igniter into the broiler igniter bracket

Place the brolier igniter bracket into position. Make sure you look at the diagram provided so the position is correct. There is a "up" & "down" side to the broiler igniter

Tightened screws & bolts on broiler igniter bracket

Reconnected the ceramic wire nuts

Inserted two mounting screws and tightened

Finished.

Oven Igniter:

Removed oven door

Removed bottom oven drawer

Removed nut that holds heat shield/disperser in place

Removedheat shield/disperser

Removed all oven tray screws

removed oven burner

disconnected oven igniter

disconneted oven igniter assembly

inserted new oven igniter

reassembled

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 21 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Wrench (Adjustable)

Customerjames from Waukesha, WI

Oven would take awhile to light causing gas fumes

I opened the oven and cleared the racks;
removed the cover of the oven heating area;
took off the nut holding the blast shield on;
removed all the screws holding the drip tray on;
some were quite rusty and fell out in my hand;
removed the 2 screws holding the igniter in;
and the one scew that allows adjustment;
pulled out the igniter and noticed the old one was connected with wire nuts while the new one had a module plug;
cut off the module plug and stripped back the wires;
applied the wire nuts;
stuck the wires back in tjhe hole and screwed it all back together-done,
I must say the best part of the repair was googling the problem "amana oven ignition troubleshooting" and getting a helpful discussion of the problem and a solution and a link to the parts suply house, It couldn't have been simpler. I got the part 2 days after ordering it online.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 9 people found this instruction helpful

Parts Used

  • Flat Style Oven Igniter

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench (Adjustable)

CustomerKeith from Denver, CO

Oven wouldn't ignite

Bought new igniter based on advice from other stories here. Didn't test the impedance. The igniter glowed, but the oven wouldn't start.

1. Removed single nut on flame pan & remove pan.
2. Removed Pan drawer and disconnected plug to igniter.
3. Removed 3 screws holding igniter in place.

Note: the screws were corroded & one stripped in removal - you may want to purchase the metal housing for the igniter assuming it comes with new screws.

4. Put everthing back in opposite order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 78