2034118-1-S-Whirlpool-31939701-Flat-Style Oven Igniter - Bake/Broil
2034118-1-S-Whirlpool-31939701-Flat-Style Oven Igniter - Bake/Broil 2034118-2-S-Whirlpool-31939701-Flat-Style Oven Igniter - Bake/Broil

Flat-Style Oven Igniter - Bake/Broil

PartSelect Number PS2034118

This igniter doesn't come with the bracket or the connector. It can be used for either the bake or broil in your appliance.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Gas igniter glows but will not light.
  • Will not start.
  • Compare At

    $44.08
  • You Save

    $7.35
  • Your Price

    $36.73
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 3 reviews What's this?
1-3 of 3
 

11 of 15 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerWilliam from Houston TX

Replaced ignitor - natural gas oven

Oven was lighting slowly and finally just stopped lighting. I ordered and replaced old ignitor with a new one. The actual repair is pretty easy. However, this is the second one I purchased, the first one was broken by me while inserting it into bracket. The active part of the ignitor (the part that heats up) is extremely fragile, more fragile than fluorescent bulb glass. Do not allow it to touch anything while inserting it. Do not drop, even a few inches. The ceramic housing meanwhile is indestructible. The wires won't have connectors on the ends so, you need to get some heat resistant wire nuts and heat resistant tape to safely splice the wires back onto the old wire mount points. Or, If you wish, you can make new connectors and wrap in asbestos sheaths and re-attach to the oven. There does not seem to be a pattern to replacing the wires in the right order. Just as long as they both are securely connected. The bracket is held by 3 screws, easy to remove and replace. You'll need to remove the old ignitor and replace the new one the same way. The elements are not screwed in, they just slide in. The old ignitor was really tight. Take care and spread bracket apart and old ignitor will slide out. The new one goes in the same way.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 10 people found this instruction helpful

Parts Used

  • Flat-Style Oven Igniter - Bake/Broil

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerBrian from Cumming GA

Stove work but your oven won't get hot ?

IF YOUR STOVE WORK'S BUT YOUR OVEN WON'T GET HOT IT IS YOUR IGNIGTER THE IGNIGHTER IN PROPER WORKING CONDITION SENDS A SIGNAL TO THE GAS VALVE SAYING LET THE GAS FLOW ITS OK. WHEN THE IGNIGHTER QUITS WORKING IT WON'T LET THE GAS FLOW AND YOUR OVEN WILL NOT GET HOT. IT IS AN EASY FIX. JUST PULL OUT ALL OF INTERIOR PARTS THE RACKS AND THE BOTTOM HEAT SHIELD THE IGNIGHTER THE WHITE STONE LOOKING PART THAT IS SCREWED TO THE BURNER WITH TWO WIRES AND IT REALLY DON'T MATTER WHAT WAY THE WIRES GO BACK ONE OF THE WIRES CONNECTS IN THE BACK SO YOU WILL HAVE TO PULL THE OVEN OUT. NOW YOU HAVE TO CLEAN UNDER IT AND YOUR DONE.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Flat-Style Oven Igniter - Bake/Broil

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerMATTHEW from SAN CLEMENTE CA

Oven would not light

Removed oven door and burner guard. Removed screws holding ignitor bracket and small panel beneath oven door. Disconnected ignitor wires behind panel and pulled out ignitor. Removed old ignitor from bracket and inserted new unit. Fed wires back down thru tubing and screwed in bracket. Connected wires and replaced panel. (Note: old ignitor glowed but would not pass enough current to operate gas valve)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3