2030883-1-S-Whirlpool-31001317-Blower Wheel
2030883-1-S-Whirlpool-31001317-Blower Wheel 2030883-2-S-Whirlpool-31001317-Blower Wheel 2030883-3-S-Whirlpool-31001317-Blower Wheel http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/35792.gif

Blower Wheel

PartSelect Number PS2030883

This wheel has a deep D-shaped shaft receptacle. The spring clamp is not included with this part.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • No heat or not enough heat.
  • Takes too long to dry.
  • Will not tumble.
  • Compare At

    $44.42
  • You Save

    $7.40
  • Your Price

    $37.02
In Stock
Order within the next 12 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 17 reviews What's this?
1-5 of 17
 

44 of 49 people found this instruction helpful

Parts Used

  • Blower Wheel

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerAlexander from Green Valley, AZ

High noise when switched on. Broken blower wheel.

Lift top off. Removed front door. Removed blower wheel cover. Replaced blower wheel. Cleaned and put back togther. Needed circlip pliers to remove circlip retaining blower wheel.

Help other customers find the most helpful instructions.

Were these instructions helpful?

37 of 58 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench (Adjustable)

CustomerDon from Elma, IA

Dryer would'nt start / drum wouldn't turn

Unplugged Dryer; used screwdriver to push in and release two clips that hold top to front, tilted top back and removed two screws holding front to sides. Disconnected door switch and removed front .
Reached in above motor to remove belt from around pulley and tensioner wheel, Pulled drum and belt out of machine.
Removed approximately 10 screws around perimeter of blower housing and removed cover to access blower wheel. Removed outer lock ring from shaft and clamp from blower wheel hub, and removed blower wheel.
Took out tensioner assembly.
Disconnected wiring connector from motor.
Removed three screws that held blower housing to bottom and removed retainer around rubber motor mount at pulley end of motor. Lifted out motor, blower housing and vent pipe as one unit.
Removed 2nd outer lock ring from motor shaft.
Rotated motor frame 45 degrees to free the rubber mount from the blower housing.
Screwed new pulley onto new motor shaft and cleaned blower housing and vent pipe.
Assembly is reverse of disassembly.
Inspected and lightly greased the glides and inspected the idler wheels before reinstalling drum.

Dryer works perfectly.

Five to ten minutes also spent unscrewing and replacing timer knob and hinge pins on lid of matching washer Crosley cw22b5v.

Very simple repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerJohn from Webster City, IA

Noisy and ineffective drying cycle due to damaged blower wheel

0. Opened packaged and receipt verified the parts against the drawing and packing slip.
1. Disconnected dryer from power source by pulling the plug.
2. Removed the two screws (philips) on left and right side of the main frame to allow access to the blower assembly.
3. (Optional)Verified power dead at the circuitry near the blower wheel assembly (former navy electrician- "check it dead").
4. Removed the two screws at the base of the wheel cover using the screw driver (philips). The other screws on the assembly cover required the use of a 1/4" nut driver.
5. Opened the assembly, and with a flathead, pried the Retaining Omega ring, and removed the damaged wheel (broken vanes and missing straight end of the center ring) and disposed.
6. Inserted the new wheel on the shaft and was able to manually do it until about 3/4 of the way; to get it fully insert it, tap it with a mallet (tap the center of the wheel and avoid the blades).
7. Insert the retaining ring and operationally test it by manually rotating the tumbler and verifying the blower wheel moves freely and without noises.
8. (Optional) Vacuumed the lint and dust from the wheel assembly, the filter and exhaust line (found several broken pieces of vanes there). Inspected heater assembly for obvious signs of damage
9. Re-installed the assembly cover and the main cover back to the frame
10. Reconnected the plug to outlet and tested by a starting a 10 minutes cycle- no noise and constant flow of air.
11. Smoked a Motecristo Churchill as I grilled the steaks and pondered the greatness of the free market.

,

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 7 people found this instruction helpful

Parts Used

  • Blower Wheel

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerSteve from Green Bay, WI

Loud rattling and grinding noise when drum is turning

Always begin repairs by unplugging the power cord from the power outlet! First, push in the 2 taps under the dryer top to lift it up and secure it at a 90 degree angle. Remove the door light switch from the retaining clip and let it hang to the outside of the dryer. After removing the 2 scews inside the top front, remove the front dryer cover. Next, remove the screws holding the blower cover and set it aside. Using a pair of plyers, remove the hose clip from the blower axle. Use a c-clip tool to remove the c-clip and pull out the blower wheel. Use a vacuum attachment hose to remove lint and other dirt from the wheel housing and dryer. Apply a light dish soap to the motor axle and slide on the new blower wheel. Replace the blower housing cover, front dryer cover, light switch, and close the dryer top, making sure to allign the pins and holes near the lid clips that secure the dryer top. Plug in the dryer power cord and you are set to go! Retire to your favorite lounge chair, grab the remote, and tell your wife that it is OK to "test" the dryer! However, do not attempt the last step until AFTER you have cleaned up all the mess you made while making the repair!

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Blower Wheel

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsPliers, Screw drivers, Wrench (Adjustable)

CustomerJulia from Evergreen Park, IL

Blower wheel broke into pieces

First we had to make the blower wheel hole bigger with a file and a dremmel tool due to our dryer being a little older model with a slightly larger shaft. Works great now, we saved ourselves about $400. and we love doing that with today's economy.
Thanks PartSelect!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 17