2030863-1-S-Whirlpool-31001192-Control Thermostat
2030863-1-S-Whirlpool-31001192-Control Thermostat 2030863-2-S-Whirlpool-31001192-Control Thermostat 2030863-3-S-Whirlpool-31001192-Control Thermostat

Control Thermostat

PartSelect Number PS2030863

L146-25F 240 Volt internal heater. This thermostat helps to regulate the dryer's internal temperature.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.
  • No heat or not enough heat.
  • Temperature too hot.
  • Compare At

    $42.88
  • You Save

    $7.15
  • Your Price

    $35.73
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 5 reviews What's this?
1-5 of 5
 

39 of 47 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerCharles R. from Kingsland GA

Dryer would not start, no enterior light operation

I down loaded the dryer schematic and itentified items that would potentially cause the observed symptoms. Initially, I replaced the thermal fuse. After the symptoms returned after two loads, suspected the hi limit thermostat not regulating the heater element temperature. I located the thermostat using the illustrated parts list on your website and replaced the thermal fuse (second time) and the thermostats using a nut driver. The Blond hasn't announced a dryer stoppage since the repair, so I'm pronouncing the repair a success. Thank you for making the drawings and schematics available.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 13 people found this instruction helpful

Parts Used

  • Control Thermostat

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerDeb from Milford OH

Dryer would not heat.

First I unplugged the dryer and slid it a few inches out from the wall. I slid 2 putty knives in the front top about 3 inches in from the sides. Released the top and raised it up. I used a multimeter to test the hi limit and the element, both were operational. I used a screwdriver to remove the 2 screws that hold the front panel in place. I lowered the panel slightly and disconnected the wires mentally noting the proper placement. With the front panel on the floor, the problem was obvious. I cleaned the lint clog under the lint screen that had caused the issue to begin with.I used a shop vac and cleaned the vent area as well as the front panel. I used a nut driver to remove the 2 screws that held the thermostat in place. The old thermostat fell apart in my hands. I covered the bare exposed wires with electrical tape. ( must have gotten HOT) and reattached the connections to the new thermostat, then replaced the 2 screws that held it secure. I stood the front panel back up and reattached the electrical connections and the 2 screws. I lowered the top and plugged it back into the outlet. I turned it on. It works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 16 people found this instruction helpful

Parts Used

  • Control Thermostat

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerRonald from Jacksonville FL

Dryer did not run at all

removed heating element, thermostat, and then replaced fuse. sorry, the control thermostat was not the problem. it was the fuse kit that failed. the control thermostat would have been easier to replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 14 people found this instruction helpful

Parts Used

Level of DifficultyDifficult

Time to do repair:Less than 15 mins

ToolsScrew drivers, Wrench set

CustomerSharie from Panama City FL

Dryer works just not heating!

Not being able to afford a new dryer we bought this dryer second hand, picked it up from the seller, moved it up a flight of stairs, plugged it in to find that it worked but didn't heat. We were so devastated and we just left it sit for a week or two because there was no time to deal with fixing it. During that time I continued to use the laundromat down the street to dry our clothes. Finally I got online to google the part number to see what I could find out and that's when I ran across this site. It gave me HOPE and all that I needed to know to fix it instead of hauling it back down those stairs and out of my life!!! First I bought an OHM meter, completely stripped down my dryer checking every part until I found one that was questionable (timer resistor assembly) and one that was definitely dead (a thermostat)...no reading! It's no wonder it was burnt out, the front cover of the dryer was impacted with lint that had no where else to go! Now I understand exactly why my mother & dad always reminded us to "clean out the lint filter". They must have gone through this once before themselves. I ordered the replacement parts late one evening and they showed up at my door by 2:00 pm the next day...it was awesome!!!!!! A big learning experience for me and it saved me a fortune. THANK YOU PartSelect, I couldn't have done it without you!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 10 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver

CustomerRobert from Manassas VA

Dryer not working at all

through the help of Parts select web site, i diagnosed the problem to the limit switch at the dryer element...I found the parts at Parts Select that included both limit switches and one control thermostat in one convient part number, the help videos are excellent, and the repair went flawlessly... basically the dryer front was removed, and then the drum with belt, that allowed me to get to both dryer element limit switches,and then replaced the thermostat at the bottom of the dryer below the drum, I reassembled the unit and it is working like new... thanks Parts Select, you saved me a lot of money.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5