2030072-1-S-Whirlpool-307249-Multi-Temp Cycling Thermostat with Internal Bias Heater
2030072-1-S-Whirlpool-307249-Multi-Temp Cycling Thermostat with Internal Bias Heater 2030072-2-S-Whirlpool-307249-Multi-Temp Cycling Thermostat with Internal Bias Heater 2030072-3-S-Whirlpool-307249-Multi-Temp Cycling Thermostat with Internal Bias Heater

Multi-Temp Cycling Thermostat with Internal Bias Heater

PartSelect Number PS2030072

This thermostat controls the internal drying temperature. Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 150 degrees Fahrenheit and a differential of 25 degrees. Meaning that with this thermostat, the heating element will cut out at 150 degrees and cycle back on once the internal temperature drops by 25 degrees.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Compare At

    $45.00
  • You Save

    $7.50
  • Your Price

    $37.50
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 3 reviews What's this?
1-3 of 3
 

7 of 8 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerBen from west Boylston MA

Noisy operation and then no heat

First I removed the two screws near the bottom of the front panel. Then I removed the front panel by rotating it outwards. Next I removed the front frame section by removing the four screws. The tumbler rests on this frame piece so remove it carefully and it will stay put - no need to take it out. The grinding noise I was hearing was the tumbler (drum) running on the frame - the glides (bearings) were worn out. This had generated piles of metal powder which I vaccumed up. It was easy to locate the reason there was no heat - the thermostat was burned to a crisp. It torched part of the blower seal in the process. The reason the thermostat fails in this manner is the lint duct gets clogged up increasing the duty cycle of the heater which fries the thermostat. I had to strip back the red wire and install a new blade connector but the thermostat just bolts on easy enough. You'll need a rivet gun to replace the glides. Drill out the old rivets and pull them out with some pliers. Easy enough to do and it runs like new! Good luck.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerCharles from Navarre FL

Dryer over heating...not shutting off or going thru cycles properly.

Opened front of dryer & watched the heating unit not shutting off. Purchased the proper high limit thermostat. Replaced it and the multi-temp cycling thermostat for good measure. My dryer runs like new with no additional problems. Thanks for making parts so readily available. Thought I was going to have to replace my dryer, but now it's fixed.....Thanks,again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 8 people found this instruction helpful

Parts Used

  • Multi-Temp Cycling Thermostat with Internal Bias Heater

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerCharles from Mount Storm WV

Heater ran constantly, except in air fluff cycle, thus operating extremely hot

Removed the frong cover and and internal sheild, removed and replaced thermostatic, wiring as original.
I had searched several other sites first for thee part, but none of them seemed accurate. Your photo matched the old exactly, giving me the confidence I wanted before ordering.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3