High Limit Thermostat

PartSelect Number PS2029367

This high limit/safety thermostat is used to prevent overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 200 degrees Fahrenheit. The element will kick back in when the temperature drops to 170 degrees Fahrenheit. Differential of 30 degrees.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No heat or not enough heat.
  • Too hot.
  • Takes too long to dry.
  • Will Not Start.
  • Compare At

    $23.88
  • You Save

    $3.98
  • Your Price

    $19.90
In Stock
Order within the next 1 hr and 25 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 11 reviews What's this?
1-5 of 11
 

96 of 125 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerAndrew from Goldsboro, NC

Unit would not come on due to blown fuse

Remove 2 front door screws and 2 side cover screws .
Remove front cover replace switches and fuses.
De- lint the blower and vent duct.
Reinstall cover door finished.

Help other customers find the most helpful instructions.

Were these instructions helpful?

30 of 39 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerRaymond from Marlton, NJ

Dryer not staying hot. Heat shuts off and doesn't come back on.

Detach front door and pop off front panel. Replaced heating unit on right and all parts on unit. Replaced cycling timer and thermostor on left. The thermostat was the last item replaced. We did this on three stages. First we replaced heating element, still had problem. Then we replaced the high limit and cycling thermostats, still had problem. Had a repairman out. He could not figure it out, because there were no error codes. He suggested replacing the thermostor. We did that and it fixed our problem. We could have saved alot if we did that first, but no one mentioned that part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

27 of 32 people found this instruction helpful

Parts Used

  • High Limit Thermostat

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set

CustomerNova from Hudson, OH

Broken contact on high limit thermostat - dryer no start

First I unplugged the dryer! Then unscrewed the two screws at the bottom of the front door. To remove the front door, swing the bottom up about 30 degrees until the two triangular hooks at the top of the door release. Then release the two wires going to the door switch from their harness so as to gain more slack to move the door out of the way. The switch was secured by 2 hex head sheet metal screws1/4inch in diameter. I used a small right angle socket wrench to get these loose. I only had to remove the front screw completely to be able to take the switch out for exchange purposes. Once this was done, reverse the process and plug it in! (BTW, the electrical schematic for this dryer is up under the top console)

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 19 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers, Wrench set

CustomerChris from Marietta, GA

Sqeaking and sqealing

Removed the front (two screws at bottom).
Marked all the wires for the door switch, bulb socket and sensor and unplugged.
Removed the barrel hanger (four hex screws two each side).
Cleaned and vacuumed internals.
Removed the front hanger and barrell.
Started with rear rollers, removed old rollers and washers.
Using 1/2" box end wrench loosened roller shaft nuts on rear of bracket.
Installed in reverse shafts, washers, rollers, snap rings.
Installed new theromstat on new element,
Removed screws from old element.
Swapped wires from one post on old element to new. Installed new element.
Reinstalled barrell, and front hanger.
Realigned new belt, making sure all clearences around idler pulley.
Free wheeled barrel, no binding.
Re-attached sensor and switch leads.
Reattached front.

Plugged in and tested successful.
Took two hours and three beers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 21 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerDavid from Plymouth, MA

Maytag dryer-no heat or heat at start-10 mins no heat

replaced high limit thermostat-303396 and cycling thermostat-306056 approx $48.00. Remove dryer door with 2 screws in hinges and 2 screws on other side.Remove front panel-pull out from top-swing down to unhinge from bottom hooks to expose parts lower front. Small socket for high limit thermostat bolts@heating element housing and same socket for cycling thermostat@blower
exhaust air housing-both easily accessible in front lower area.Unplug power before working inside.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 11