2027829-2-S-Whirlpool-27001113-Timer - 120V 60Hz
2027829-2-S-Whirlpool-27001113-Timer - 120V 60Hz 2027829-1-S-Whirlpool-27001113-Timer - 120V 60Hz 2027829-3-S-Whirlpool-27001113-Timer - 120V 60Hz http://www.partselect.com/Schematics/Maytag/55264.gif

Timer - 120V 60Hz

PartSelect Number PS2027829

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not drain.
  • Compare At

    $152.21
  • You Save

    $25.37
  • Your Price

    $126.84
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 16 reviews What's this?
1-5 of 16
 

15 of 16 people found this instruction helpful

Parts Used:
  • Timer - 120V 60Hz
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Susan from Hillsboro, KS

Washer wouldn't cycle through. It would only do 1 cycle.

I unplugged the washer, then unplugged the timer, which is really easy because it is just like unplugging a computer. I took the dial piece apart. Unscrewed the screw that was holding the timer on. Took the timer out and re-assembled the dial, then plugged the timer back in and then plugged the washer back in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 11 people found this instruction helpful

Parts Used:
  • Timer - 120V 60Hz
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: David from Holcombe, WI

Washer wouldn't advance to next operation of cycle

First I unplugged the washer from the power supply. I then removed the cover from the timer selector, by gently prying with a flat screw driver. I next removed the small plastic pin in the center of the selector with the screw driver. The remaining part of the seletor can the be pulled from the timer shaft. I then removed 3 phillips head screws from the top of the rear control panel. The bottom of the panel is secured with 3 1/4" screws, which I removed with a nut driver. The panel can then be tipped towards the front of the machine to allow access to the timer. I unplugged the electrical plug and removed the screw which holds the timer. Next slide the timer to the left and lift it out. Reverse the procedure and your ready to test youur handy work.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used:
  • Timer - 120V 60Hz
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: david from jasper, AR

Washer would not finish cycle

replaced timer, be careful not to try to pull the outer knob off without prying out the center of it and then removing the retainer.Then you can remove the 3 piece adjusment knob that sets your washing cycles. If you do not remove it this way you will damage the timer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used:
  • Timer - 120V 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: gerald from sarasota, FL

Would go through cycle without hitting the spin cycle

removed screws from back - took off knob on the front of the timer. I then unplugged the old timer and plugged the new one in.

It was very easy

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used:
  • Timer - 120V 60Hz
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: David from Thomaston, CT

Machine stopped spinning the water out after wash cycle. The timer would advance, but the original wash water was still in tub at the end of the cycle.

The repair was super easy and fast. I removed the back of the control panel with screwdrivers (3 flat head screws, 3 phillips head screws). Then I removed the front of the knob from the timer by removing the plastic center cover cap, plactic inner clip and lifting out the inner ring. The timer was secured by only one screw, which I removed. The wiring assembly was easy to unplug. Then I popped out the timer by sliding it to the left to clear the clips. I replaced the old timer with the new one, secured the single screw, plugged the wire assembly in, reseated the timer knob on front and replaced the control panel cover. The problem was solved and the machine works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 16