Drain Pump - 120V 60Hz

PartSelect Number PS2026591

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not drain.
  • Leaking.
  • Pumps but will not spin.
  • Compare At

    $130.58
  • You Save

    $21.76
  • Your Price

    $108.82
In Stock
Order within the next 7 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 5 reviews What's this?
1-5 of 5
 

58 of 64 people found this instruction helpful

Parts Used

  • Drain Pump - 120V 60Hz

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDeborah from Westfield MA

Old pump stopped draining the machine- impeller in pump wore out

FIRST- I UNPLUGGED AND COMPLETELY DRAINED MACHINE OF WATER BY PUTTING HOSE AT GROUND LEVEL NEAR DRAIN .

SECOND- REMOVED BACK PLATE TO WASHER
SAVING ALL HARDWARE.

THIRD- DISCONNECTED IN AND OUT HOSE TO PUMP. TWISTED PUMP GENTLY AS TO POP IT OUT OF SLOTS IN BOTTOM OF MACHINE.

FOURTH- DISCONNECTED WIRES TO OLD PUMP HOOKED TO NEW PUMP REPLACED PUMP, REPLACED HOSES- TESTED MACHINE THEN REPLACED BACK PLATE OF MACHINE. DONE.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 17 people found this instruction helpful

Parts Used

  • Drain Pump - 120V 60Hz

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDrake from Crofton MD

Broken pump

Roll washer out of drain pan on section of 3" PVC pipe. Unplug washer & disconnect hoses. Remove rear access panel with nutdriver. Disconnect wiring harness from pump. Disconnect hoses from pump using screwdriver and pliers. Twist pump counter-clockwise to separate from bottom of washer housing. Transfer electronic component from old to new pump. Install new pump in reverse order as above.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 16 people found this instruction helpful

Parts Used

  • Drain Pump - 120V 60Hz

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerScott from Sedalia MO

Washer would not drain

Starting out I found the code that the washer was showing,ND, Meaning no drain so I read up on and people where saying that the pump had a blockage in it, so I took the back of the washer to gain acess to the pump, I took the drain hose off to look in side to see if there was a problem there was nothing in the pump itself so I started to remove the pump I undid the wiring harness to find the problem, the red wire to the pump had burned in the harness order the part from part select and 30 minutes later my wife was doing laundry again..........Thanks partselect for the fast shipping and quality parts very easy repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 13 people found this instruction helpful

Parts Used

  • Drain Pump - 120V 60Hz

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Wrench(Adjustable)

Customerdeb from new madison OH

Washer would not drain water

my husband took the old part off. order the new part thru your company...3 days later the part came in. then he reattached thee part to the hoses with the champs and we said alittle pray and i had my washer back

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 14 people found this instruction helpful

Parts Used

  • Drain Pump - 120V 60Hz

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerDavid from Watervliet MI

Pump would not pump water from washer drum

It was very easy to do. I took the back cover off. I dissconected two hoses. disconnected one wire. removed a small plastic bag (cover over wires). turned the pump 1/4 turn.and reversed this process with the new pump. It took me 15 minutes to remove and replace. Put the washer thru a cycle and it worked!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5