2025108-1-S-Whirlpool-23748-Retaining Ring
2025108-1-S-Whirlpool-23748-Retaining Ring 2025108-2-S-Whirlpool-23748-Retaining Ring http://www.partselect.com/Schematics/Maytag/17847.gif

Retaining Ring

PartSelect Number PS2025108

Sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Will not tumble.
  • Will not agitate.
  • Pumps but will not spin.
  • Compare At

    $6.11
  • You Save

    $1.02
  • Your Price

    $5.09
Special Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Thrust Washer

Part Number 333174

This washer is 3/4 inches in diameter.

$4.45
On Order

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 36 reviews What's this?
1-5 of 36
 

134 of 201 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: David from Underwood, IA

Loud banging sound. Worn out roller.

Pulled off the lower panel with 5/16 socket.Pulled off the door assembly by removing the two screws at the bottom of the door assembly. I pulled down a little and then out. be carefull of the wires. Other posts said to remove. The wires were long enough I did not have to remove them. I just leaned it against the wall. I then removed the 4 screws that hold the front piece in.pulled it off replaced brackets , installed self adhesive felt(stuck good) and then glides. Mine were thin but not the problem. I then reached under the drum and released the belt from the tensioner. I then pulled the whole drum out.This is the time to vacum out good. I could get to the rear rollers very easy. The left roller was shot and the shaft half wore into(the problem). I pulled off the two screws holding the roller support. Normally You have to remove the wheel with snap ring pliers first to remove the support. In this case snap ring long gone. Replaced support shaft, installed thrust washers and roller with grease for both sides. The right support shaft was still good. Removed tensioner pulley and inspected. It was just as good as the new one. Cleaned and greased and reinstalled. Put new belt on the tub and slid it back in. Be carefull to get the belt on the proper side of the tensioner. I then installed the front supprt in place to support the tub with the 4 screws. Spun the tub(felt good) then reached under and reinstalled belt to motor and tensioner. Spun again to check for belt alignment. (Check) Reinstalled door an lower panel. Test Quiet Sounds like new. Very easy! I hope this helps someone just as the other post has helped me. Blessings to all.

Help other customers find the most helpful instructions.

Were these instructions helpful?

86 of 151 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Bryan from Everett, WA

Dryer would make hmming noise and motor was loud like there was some resistance. Dryer would overheat and shut down

I removed the covers, released the belt, pulled the drum, replaced rollers, glides, idler pulley and motor. The motor was the main issue but I replaced the rollers, idler and glides while I was in there. My biggest challenge was the clips that hold the motor in place. The hooked over a metal ear. I was able to use a big strait slot with downward pressure to release and reinstall.

The illustratations on the web site made ordering the correct part easy and the part fit perfectly so this repair job could have been accomplshed by anyone with very basic mechanical understanding.

Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

29 of 34 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Customer: JOHN from CORPUS CHRISTI, TX

Dryer would squeal when drying clothes

Unplugged dryer, turned off gas, raised front of dryer with two 2X4's on edge resting on legs, removed two lower panel screws, removed lower panel. Removed lower blower & filter assembly, screws (3) are on the inside of drum. (Good chance to clean it out) Removed two lower front upper main panel screws. Supported top panel with wood for access. Removed panel slowly, marked wires that go to door switch, set panel aside. Removed tension on belt by reaching in on the right lower side and unhooking the tensioner from belt, look to see how it is installed, for reinstallation on assembly. Pulled drum out slowly as not to damage seals on drum. replaced parts, attached with self tapping screws.(screws all the same size) reassembly in reverse order. Will need to put belt on drum before installing drum. Check drum alignment with rollers and seals. Used very small amount of high pressure grease on roller bracket and shaft assembly where the support roller shaft spins for lubrication. All's quiet. (Vacuumed out inside while dissassembled)

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 21 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools:
Customer: KATHLEEN from HUDDLESTON, VA

Loud screeching sound ....needed motor instead!

I am a widow. Had to pay for labor. He said it was motor. I said I would think about it. I looked on line at your site. Found symptoms that pointed toward idler pulley wheel with bearing, etc. Your site said: ZERO PERCENT CHANCE LOUD SCREECHING WAS MOTOR! So I ordered all parts above. I called repairman to return; he assured me he tried it enough to be assured it was motor bearings. So, I placed another order with you for a motor. Repairman just installed motor, screeching is gone! We installed the belt, pulley, etc..few of the above parts since dryer is old. PLEASE UPDATE YOUR WEBSITE TO INCLUDE MOTOR (BEARING) AS POSSIBILITY FOR LOUD SCREECHING.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Socket set, Wrench set
Customer: James from North Kingstown, RI

Dryer making loud squeeking noises

The pully wheel was completely worn down as the belt had cut into it over time. I'm not sure if the lever and shaft needed replacing but since the part was inexpensive I decided to replace it as well as the wheel. The easiest way to access the parts was to turn the dryer on its side and remove the bottom panel of the dryer. This eliminated the need to remove the drum. It was then easy to reach in with a wrench and remove nut and bolt that held on the pulley lever. I also had to remove the spring which was attached to the lever. Next I put the new pully wheel on the shaft of the new pulley lever. The most difficult part of the job was installing retainer clip which holds the wheel on the shaft. This took a little persistance. After this was done it was simple to put the assembly back in place, reattach the spring and tighten the nut and bolt. I then replaced the bottom panel of he dryer, turned it upright and plugged it in. The whole job took just over an hour. One tip: Before removing the old assembly, I took a picture of it with my cell phone camera so I would remember how it went back together.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 36