2022105-1-S-Whirlpool-22213057-Injector Sleeve Bracket - Side Mounting
2022105-1-S-Whirlpool-22213057-Injector Sleeve Bracket - Side Mounting 2022105-2-S-Whirlpool-22213057-Injector Sleeve Bracket - Side Mounting http://www.partselect.com/Schematics/Maytag/37308.gif

Injector Sleeve Bracket - Side Mounting

PartSelect Number PS2022105

This injector sleeve bracket is white and made entirely of plastic. This is a side mounting style bracket.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Compare At

    $9.32
  • You Save

    $1.55
  • Your Price

    $7.77
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Injector Valve Kit

Part Number 2003241

This kit contains the injector, nozzle and worm clamps. The injector and nozzle are also sold separately.

$12.10
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 11 reviews What's this?
1-5 of 11
 

24 of 27 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Richard from Ashley Falls, MA

Washer was leaking onto the floor

First I disconnected the power and turned off the water supply. Then removed the front panel of the washer by removing the two phillips head screws from the lower left and right front of the machine. I then removed the four hex screws at the corners of the top of the machine using a socket set. The two screws in the front of the top come out through the inside and the two screws in the back come out through the access holes in the top. Next I disconnected the bleach/softener tube from the upper end to allow the lid to be raised. Then I swung the right hand side of the lid up fully and rested it on the left hand side support using the braces provided on the lid and resting the weight on the attached support string. The injector valve, inector nozzle and injector bracket are right on top on the left hand side. The bracket is taken out by removing one hex screw on the underside of the bracket. The valve and nozzle are removed by loosening the hex screw on the hose clamp, To replace, first assemble the rubber sleeve and plastic injector. The large end of the plastic injector should fit squarely into the slot of the rubber sleeve. To insert this assembly back into the molded end of the injector hose I used a small amout of laundry detergent to lubricate the large end of the rubber sleeve. This allowed the part to slide in without displacing the rubber sleeve from the plastic injector nozzle. Now, I replaced the associated parts (lid and front panel) and turned the water on and plugged the washer back in. No more leak. Thanks to PartSelect.com my repair was easy. I did not need to replace the injector sleeve bracket but purchased the new one in case I broke the old one during the repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 20 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: DAN from McDONALD, PA

I saw a leak coming down outside of washer.

I took off the front of machine by taking out the two screws at bottom of front panel. As I turned the water off and on I could see the leak coming from the sleeve bracket area. Using a small socket I was able to loosen the screw and pull apart the hose from the valve and replace with the new valve in about 30 seconds. Tightened everything back up, turned on the water again--all dry! Put panel back on and good as new!

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 9 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Paul from Huntington Beach, CA

The hot water intake valve did not function

This clothes washer is 35 years old and runs like a champ. I did notice a bit of water below the left rear and assumed that a hose was leaking. I let it go for about 6 months, until I could fit it into the "to-do" list. During that time, the hot/cold water intake valve died. I ordered the replacement hot/cold valve a month ago but noticed, upon removal of the valve, that there was significant water drip evidence around the electrical valve solenoids. The water drips caused the valve to die. Drips came from a clogged injector hose air break directly above the valve. Replaced all hoses and water level vacuum air line. Very easy process. The front drops off with two screws. The lid is off with two screws. All hoses easy to R/R. It took about 2 hours to complete. All replacement parts were perfect. My belts are fine so I'm ready for another 30 years of service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: Rene from Yakima, WA

Water was going all over the floor

My washer is very old but in very good condition, it was my mothers when I was a teenager and now I am 50! This is the first repair ever done on it, my son was sure I should just buy a new one but my daughter and I had other ideas. We went on line and looked it up and followed easy directions and found the small part that was leaking right away.It had just worn out. we then ordered the parts for under $20.00 and within a few day's it was here and we were back in the laundry washing. Thank you soooo much, we are not going to let this one down with my son for some time =)

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Matthew from Coloorado Springs, CO

Washer leaked at injector valve site

Removed two screws from bottom of front cover. Raised front cover to disingage clips and remove. Removed two screws to release top cover. Propped top cover up with mop to allow access to injector site. Removed two clamps to free injector sleeve, nozzle and valve from inlet hose. Installed new clamps, sleeve, nozzle and bracket. Lowered top cover and tested for leaks. None found. Reinstalled top cover. Reinstalled front cover. Washer back in service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 11