2021510-1-S-Whirlpool-22003989-Timer Cap
2021510-1-S-Whirlpool-22003989-Timer Cap 2021510-2-S-Whirlpool-22003989-Timer Cap

Timer Cap

PartSelect Number PS2021510

This timer cap is chrome in color.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.
  • Timer will not advance.
  • Compare At

    $23.70
  • You Save

    $3.95
  • Your Price

    $19.75
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Timer Knob

Part Number 2021514

This is the second part of a three-part knob. The cap and the skirt are sold separately. This knob is blue and white in colour.

$15.37
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 9 reviews What's this?
1-9 of 9
 

7 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerNancy from Seminole FL

Knob pulled off and I had been turning it on with pliers

removed the 3 screws holding the front cover on to the timer, unsnapped the timer, unpluged it and plugged in the new one then snapped it back in place. put the front cover back and placed the timer cap back on it works like new now and saved me $140 dollars. Very happy to not look like I am trying to extract a tooth when turning on the dryer

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 8 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerAlbert from Alger MI

Drying timer won't advance

Remove the timer control knob cap with a small flat head screw driver on either side of the cap, between the cap and the rubber ring (this took a while to figure out, but it's easy once you do) then remove the knob. Remove 3 T15 hex screws on top of control panel, tilt top of panel toward you and lift up. Remove the electrical connector (this was difficult, you have to release the lock and rock the connector at the same time). Push down on the locking tabs at the feet of the timer assembly and slide to remove. Reverse these directions to install new timer. Unfortunately this did not fix my problem because the timer still won't advance. I'm replacing the sensor assembly next. I'll let you know if that works.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerJohn from Sterling Heights MI

Knob broke off dryer timer

The two parts purchased were the corrects parts needed to do the job. (There's always a first time for everything!) When the plastic timer knob broke away from the timer stem, it left the silver timer cap's locking pin embedded in the timer stem. I could not remove the broken remains of the knob while the broken off pin was still in place. And it was impossible to grip the pin with pliers or tweezers without damaging the timer stem. As a solution I grabbed my whole-house vacuum cleaner hose and sucked the broken pin out of the timer stem. Total time of repair was about 20 minutes not including the two-hour brainstorming time-out that led me to the vacuum cleaner solution.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 10 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerSudeepto from San Diego CA

Broken plastic twirl knob shaft on timer assembly and chrome timer cap

0. Disconnected the dryer power supply
1. Removed the control panel (3 screws, star bit)
2. Detached the electric power supply cords from the timer assembly (took a bit of easing back and forth - do not pull by the electric cords, pull the socket itself)
3. Timer assembly eased off subsequently (held in place by three unscrewed receptacles)
4. Installed the new timer assembly, plugged back the supply cords, and installed the new timer knob, skirt and chrome cap.

They don't build Maytag equipment as they used to. We bought a fridge, washer and dryer 6 years ago - all three of them have had component, part stress and/or electronic sensor failures :-(

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerRa from Saugus MA

Dryer timer has broken gears.

My dryer timer's internal gears were broken. Timer Cap also was broken. I opened the front face plate by removing the three screws on top and disconnecting the wiring harness. Took me 10 minutes to replace. I do very very little shopping online, I am VERY impressed with the availability of parts from partselect and am also impressed with the shipping turnaround. I thought I needed a timer knob but then realized I didn't need it and canceled the order, and I was refunded in two days. I am so happy with the way the process went I wish partselect dealt with other products besides appliances.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerBobby from Ridgely TN

Dryer would not run=bad timer

simply replaced the timer.thank you for perfect service

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerAndrew from Beaver Falls PA

Timer knob was broken so the knob would not stay on

I removed the silver cap and then removed the knob itself. I replaced the knob with the new part and also the silver cap with the part. The job was complete.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Timer Cap

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

Customerjames from wilmington NC

Cap broke

pop cap on knob

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerNancy from Fairfield NJ

Time cap broke away from timer

Removed Screws on panel, pluged new timer into wire replace panel, but on new knob and cap and it was ready to go.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-9 of 9