2021083-1-S-Whirlpool-22003499-Timer
2021083-1-S-Whirlpool-22003499-Timer 2021083-2-S-Whirlpool-22003499-Timer 2021083-3-S-Whirlpool-22003499-Timer http://www.partselect.com/Schematics/Maytag/53165.gif

Timer

PartSelect Number PS2021083

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will not drain.
  • Will Not Start.
  • Pumps but will not spin.
  • Compare At

    $138.17
  • You Save

    $23.03
  • Your Price

    $115.14
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 12 reviews What's this?
1-5 of 12
 

29 of 31 people found this instruction helpful

Parts Used:
  • Timer
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Thomas from Vineland, NJ

Washer would skip the rinse and spin cycle and just keep on washing

1. Removed 3 phillips head screws and 2 hex head screws from upper back cover to expose the timer.
2. Removed the dial knob on front by popping off the cover with a screw driver then pryed up a smaller plastic button used to hold the knob in place.......knob slid off.
3. I then was able to tilt the whole panel forward to gain total access.to the wiring and timer
4. Disconnected wire harness from the switch.......had to pry up the snap tab that holds it in place.
5. Had to remove a small electrical board attached to the back of the timer......used screwdriver to pop it up and out (gently).
6. Removed one hold-down screw, lifted a little lock-tab and slid the unit to the left and lifted out and replaced.
7 . Reversed the above steps to install. This is not hard at all .>>.very easy to replace.
Machine works perfectly and I saved a couple hundred dollars for an appliance technician.
Thanks to the previous poster . I copied some of their comments and added some other comments..

The service and prompness from Parts Select was excellant and quick delivery.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 15 people found this instruction helpful

Parts Used:
  • Timer
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Gary from Temple City, CA

Washer was not running thru rinse cycle

Removed upper back cover to expose the timer, the whole panel could then be tipped foward which made it easy to work on.
Removed the dial knob on front by popping off the cover then pryed up a smaller plastic button used to hold the knob in place.......knob slid off.
Disconnected wire harness from the switch.......had to pry up the snap tab that holds it in place.
Had to remove a small electrical board attached to the back of the timer......used screwdriver to pop it up and out (gently).
Removed one hold-down screw, lifted a little lock-tab and slid the unit to the left and lifted out and replaced.
I'm sure I forgot something.........but the whole thing was pretty easy to figure out .

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 9 people found this instruction helpful

Parts Used:
  • Timer
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Screw drivers
Customer: Javier from Houston, TX

The washer started working and skipped the rinse and spin cycle at the end it was full of water.

The repair it is simple the problem was to figure it out, I did some research on this kind of problem and everything was pointing to the timer so I used a philips screw driver and a nut driver to remove the backside of the control panel,but first don;t forget to unplug the machine, I have to pry off the knob top cover and remove a plastic clip to pull the knob after that you can unplug the electronic board connector and the timer connector,remove a couple of screws amd the timer is out, installation is the reverse of removal.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: randy from Dayton, NV

The timer housing is to thin. I broke the tab on the right side installing the timer.

I did what anyone could do, remove the screws and replace the part. The part just came apart during installation. If I were Maytag, I would replace the part free of charge.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used:
  • Timer
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: Gary from Red Lion, PA

The washer would stick in between cycles and not continue

Removed the back panel from the control panel which was 3 phillips head screws and 2 hex screws. Remove the front knob from the timer, this is completed by removing the round center plate on the knob by simply pulling it off and then remove the small plastic pin in the center of the knod underneath the round plate. The pin holds the knob in place and once removed the knob can be pulled off along with the plate behind it.

Now from the back inside the contrlo panel simply unplug the wiring harness from the timer. Remove the circuit board from the timer also, it pulls off easily. There is one hex head screw holding the timer in place and once removed the entire timer assembly can be removed by rerleasing the right side and sliding the assembly to the right and out.

Slide the new timer in place, secure with the hex head screw, reconnect the wiring harness and press the circuit board back in place on the bottom of the new timer. Close up the back panel and replace the front knob components onto the new timer and you are ready to go. In all it took about 40 minutes and saved me over $200 for a service call.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 12