2020911-1-S-Whirlpool-22003285-Tub to Drain Pump Hose
2020911-1-S-Whirlpool-22003285-Tub to Drain Pump Hose 2020911-2-S-Whirlpool-22003285-Tub to Drain Pump Hose

Tub to Drain Pump Hose

PartSelect Number PS2020911

This tub to pump hose is all black in color and is made of plastic.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Leaking.
  • Compare At

    $16.94
  • You Save

    $2.82
  • Your Price

    $14.12
In Stock
Order within the next 34 mins and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 6 reviews What's this?
1-6 of 6
 

14 of 17 people found this instruction helpful

Parts Used

  • Tub to Drain Pump Hose

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Pliers

CustomerBrian from Lynbrook NY

Leaking pump hose

I thought I was going to need to replace the leaking washer machine. Water was every where and after checking the main sewer drain was ok I lifted the washer and found the water pouring out the bottom when i put it on.
After finding out how to get the whole top open and the front panel off I was able to locate the source of the water leak on my washer machine. The cause was split in the plastic hose that goes from the tub to the pump. After the new hose arived I was able to replace it within 10 minutes. So far so good. Thank you Part Select.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

  • Tub to Drain Pump Hose

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRichard from Cedar Park TX

Water leaking under washer. Tub to pump hose sprung a leak.

There are two clips that hold the top of the washer down. Releasing these clips allows you to lift the top; it is hinged at the back. Then remove two screws holding the front panel and remove the front panel. The tub to pump hose is easily accessible. It is held in place by a hose clamp at each end. Use pliers to squeeze the clamps and remove the hose. Replace with new hose. I re-used the original clamps.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Tub to Drain Pump Hose

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerHuston from columbiana AL

Water in the floor

take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Tub to Drain Pump Hose

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers

CustomerJERRY from LEXINGTON NC

Washer was leaking when water was pumping out

took a putty knife and raised the top,then took two bolts out, then pulled front panel off. took hose off from the tub to the pump,and put the new one on. It's working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 2 people found this instruction helpful

Parts Used

  • Tub to Drain Pump Hose

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsPliers

CustomerRussell from Aplington IA

Water on the floor

figured out how to open the top of the washer(Two small tabs I pushed in with a putty knife. Looked for the area it was leaking. Slide the hose clamps off with a pliers and pull out hose.

Put clamps on new hose, replace hose and slide clamps to ends to seal the connections

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

  • Tub to Drain Pump Hose

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

Customerwilliam from norristown PA

Water leak

pop top,remove 2 screws,remove front panel.remove 2 spring clamps from tub hose.reverse!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6