Remote Style Pump with Motor - 120V 80W

PartSelect Number PS2020805

This assembly comes with a check valve and helps expel water from the washing machine once spin speed is maintained for a specific period of time.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not drain.
  • Leaking.
  • Pumps but will not spin.
  • Noisy.
  • Compare At

    $103.08
  • You Save

    $17.18
  • Your Price

    $85.90
In Stock
Order within the next 5 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 19 reviews What's this?
16-19 of 19
 

1 of 2 people found this instruction helpful

Parts Used

  • Remote Style Pump with Motor - 120V 80W

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerThomas from Rochester NY

Washer will not drain

Disconnect power. Remove back panel. Use shop vac to remove water from drum. You can also remove one of the agitator fins from the drum (uses 2 TORX screws) to gain access to inner tub drain hole to remove additional water with shop vac and check for obstructions. Remove power wires from pump, noting position of each. Place towel near pump and disconnect input and output hoses. Rotate pump to disengage from slots in base, and remove. Installation is reverse.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Remote Style Pump with Motor - 120V 80W

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench set

CustomerDanvardys from Powder Springs GA

Washer wouldn't drain

The first step to repairing this problem is to remove the hoses and back panel of the washer. Next detach both the hoses attached to the pump ( have some towels handy because their will be a lot of water pouring out of the pump). Before removing any screws on the pump, use a wrench to remove the bottom platform securing the pump inside of the washer. On the the Amana washer there should be about three bolts holding this small platform down. After unscrewing the bolts, unsnap the wire connected to the motor and remove the platform to get the entire pump out of the washer. The next step is to unscrew the screws on the bottom of the platform to release the base of the pump. The next step is to put the new pump on that same platform. FYI the new pump may not fit on the platform. To solve this problem, unscrew the motor/pump(the black thing) from the base holding the motor( the cream or white colored part). Do this step for the old and new motor/pump. Screw your new motor to the old base. Screw the base with the motor attached back on the platform. Connect the wire in the washer back to the motor. Screw the platform back in the washer and reconnect everything that was disconnected to remove the motor/pump. Finally put the back panel back on the washer and run a test cycle. The washer should now be able to drain.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Remote Style Pump with Motor - 120V 80W

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerRaymond from Berea KY

Water wouldn't drain

Tilt washer onto door with back of washer on top for easier access.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerROD from HENDERSONVILLE TN

Washer would not pump water out

Unplugged washer
Loosened 2 hose clamps with nut driver
Unplugged 2 power wires with pliers
Twisted motor in washer base to align with large holes and removed it
Attached wires to new motor
Replaced new motor, twisted back in base
Attached 2 hoses and tightened hose clamps
Test washing worked fine

Hose outlet no longer available with cylindrical filter, so current hose without filter is being used.

Lint fiter simple front load replacement for old one in Maytag MDE3000AYW dryer.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16-19 of 19