Timer

PartSelect Number PS2020347

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.
  • Compare At

    $136.52
  • You Save

    $22.75
  • Your Price

    $113.77
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.6 / 5.0, 4 reviews What's this?
1-4 of 4
 

11 of 14 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set, Wrench set

CustomerWilliam from Jennings FL

Washer would not drain

Since the machine would not drain, I suspected the drain pump. A friend in appliance repair tested that for me and it was good. All one has to do with that is hook a test line to the pump with 120 volts and if it runs it is good. He then told me to see it the mother board which is located in the right upper area above the dryer drum had a burned place at a resistor and to note if the door would not lock. I checked this and the circuit board was not damaged and the wax motor which locks the door was working OK. (This unit is a combo stack dryer and washer) I then suspected the timer because my wife told me that it had been making a grinding noise. The timer was replaced by the one you sent me and it solved the problem. ( My friend really did not want to work on this machine since he had replaced the inner drum and bearing about six months ago and it took all day)Thanks a bunch. The timer came in one day from the time of order.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 4 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Screw drivers, Socket set

CustomerWilliam from Jennings FL

Door problem on maytag stacked washer/dryer

Power would not shut off unit after washer finished wash cycle. Had to push power off button to take power off and allow door to unlock. Put new timer on and it did not fix the problem. Replaced the two micro switches involved with the wax motor and that did not fix the problem. Finally, I smelled electrical wiring smoke and found that the mother board had a burned resistor (#11). This then told me that the problem was in the wax motor. Ordered a new wax motor and a new mother board (located at the top right above the dryer) and the washer is working fine. It was through my lack of experience that caused all of this trial and error. If you have a problem with the washer door not locking or not terminating power after the cycle, I think that you should suspect the wax motor first. If the mother board resistor is not burned you may get away without that expense by replacing the wax motor or the spin enable micro switches first. The control board is expensive so it is best to check the micro switches for proper operation and if they are OK, I would put a new wax motor on the washer. These have caused the Maytag a lot of trouble and they have a revised motor now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 4 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerKen from Lyndhurst OH

Was not cycling

Figured out it had to be the timer after checking unit out and with a little research. Ordered a timer, it was so simple to replace just unscrewed cover and removed timer, it just plugs in, hooked it back up works like a charm.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

  • Timer

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerArnie from Underwood IA

Dishwasher would not run thru rinxe cycles

after hiring qualified service company to fix unit, bought timer from you per diagnosis to save $325
unplugged device removed front cover covers removed mounting screws
unplugged wire harness
removed timer,
reversed process
turned on dishwasher, same problem
new timer did not remedy problem
Discovered troubleshooting table on back side of schematic behind front cover, read problem is plugged screens in water lines.
cleaned screens problem solved. wife is happy

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-4 of 4