2020221-1-S-Whirlpool-22002290-Dispenser Bezel
2020221-1-S-Whirlpool-22002290-Dispenser Bezel 2020221-2-S-Whirlpool-22002290-Dispenser Bezel http://www.partselect.com/Schematics/Maytag/59113.gif

Dispenser Bezel

PartSelect Number PS2020221

This part mounts to the top panel of the washer and houses the dispenser.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $26.18
  • You Save

    $4.36
  • Your Price

    $21.82
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Related Parts Additional or alternate parts to consider.

Part PhotoPart DescriptionPriceAvailability

Dispenser Lid

Part Number 2021882

This part is used to cover up the dispenser.

Order within the next 12 hrs and your part ships today!
$16.84
In Stock

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 23 reviews What's this?
1-5 of 23
 

76 of 114 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: richard from austin, MN

Drains but doesn't spin, door lock does not engage.

Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 18 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Bradley from Round Rock, TX

Trips imbalance too easily; wouldn't drain

Removed front door and front skin, tipped up top cover and replaced two front suspension springs (added grease lube onto spring hooks.) Tipped machine forward onto its front face, removed rear cover then removed rightside strut assembly. Installed new then removed left strut assembly. Installed new. Tightened all components. Repaired broken power wire to the remote pump. Tipped back upright, restored all skins and tested function. Washer was fully repaired with excellent cleaning results.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 16 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set, Wrench set
Customer: Glenn from San Jose, CA

Ancillary work when replacing noisey tub bearings

The replacement for the drive belt and dispenser bezel were part of a bigger job of changing the outer tub bearings. Those familiar with Maytag Neptune washers will experience the jet-taking-off sound when the tub seals wear and water gets into the bearings. While I would have the machine open I thought I would change the drive belt. I also noticed the dispenser bezel had two of the four mounting corners broken.

Replacing the bearings was done. I purchased the bearings and rented a bearing puller made especially for this job

After the bearing and seal replacement, I put on the new belt. It was almost straight forward. Almost because the belt didn't just slip on. The new belt is much smaller than the old belt. Not having the grip strength of Mr. Atlas, I was not able to hold the belt on the pulley rim while turning the pulley around, as the instructions say. The other thing that makes this difficult is that the ribs on the outer tub are quite close to the spokes of the pulley. I was not able to firmly grasp around the belt and pulley with one hand and turn the pulley with the other. My knuckles seemed to get in the way (ouch!).

Being an electrical engineer, I happen to have cable ties handy. I used one to hold the belt on the pulley rim, and was able to turn the pulley with two hands (still watching out for my knuckles).

For the dispenser bezel, I took the old dispenser lid and hinge pins off the old bezel by cutting the bezel between the hinge points, then transferred them on the new one.

On the washer top cover, there was a lot rust around the dispenser opening. So before closing up the machine and installing the bezel, I removed the loose rust, then applied a rust converter. The rust converter was in an aerosol can, and since I was working on the washing machine inside the house and not wanting to make a mess, instead of spraying the cover, I sprayed onto a paper towel then dabbed the chemical onto the rusty spots. I finished with an appliance epoxy paint around the dispenser opening.

I'd like to say I was impressed with the service from PartSelect. I ordered on Saturday, they shipped on Monday, and the parts arrived on Tuesday morning, and this was with standard shipping. On Thursday I was ready to put on the belt, but there was also a problem where one of the motor isolators was missing from the belt kit. I called in the shortage and they shipped the next day and the new belt kit arrive on Saturday. I noticed the shipment was from Fresno so they must have a warehouse there.

So all in all, the drive belt and dispenser bezel were simple to install. Certainly they were the easiest parts of the job.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Brandon from Berea, OH

Bad pump

I took off the rear panel and removed the hose clamps and electrical terminals, slid pump out of slot in bottom pan of washing machine. It only took minutes, this was part of a major overhaul. I replaced this as a precautionary measure. Great prices and quick service,

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: KENNETH from Portsmouth, RI

Top of dispenser broke at hinge

Removed 4 screws holding dispenser frame. Removed old & installed new frame. Top, hinged lid needed to be slightly bowed so hinge pins could be fit in holes. End of repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 23