2020195-1-S-Whirlpool-22002263-Light Bulb - 10W
2020195-1-S-Whirlpool-22002263-Light Bulb - 10W

Light Bulb - 10W

PartSelect Number PS2020195

This ten watt appliance light bulb is used with both washers and dryers. Sold individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $10.74
  • You Save

    $1.79
  • Your Price

    $8.95
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 12 reviews What's this?
1-12 of 12
 

31 of 38 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set

CustomerLarry from Panama City Beach FL

Squeeling on startup and intermittently during use

First, I read reviews on this forum. Great help! I was betting, from previous reviews, that it was a drum roller. I took everything apart prior to ordering any parts. Sure enough, one drum roller was seized on the roller shaft. Decided to replace all rotating parts (rollers,shafts, belt, idler pulley) while everything was apart. I also took the opportunity to clean out all of the lint (there was a lot) from the motor and intake.
Parts were on my doorstep in two days. The dryer is like brand new. I could do this job again in less than an hour. This was money and time well spent.

Help other customers find the most helpful instructions.

Were these instructions helpful?

28 of 33 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsScrew drivers, Socket set

CustomerEdward from Andover NJ

Dryer was sqeaking loudly when running

I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan

Help other customers find the most helpful instructions.

Were these instructions helpful?

20 of 24 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerAngela from Houston TX

Dryer would stop running after several minutes. Once cooled it would start again. Motor worn out and binding.

Remove back cover
Raise top
Remove filter assembly
Remove front cover and drum

Tip: Use an end wrench on the fan and another on the pully shaft of the motor to remove fan from motor prior to removing motor from cradle.

Vacuum everything while disassembled

Remember to take your time and not force anything and this will go smooth.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 18 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

Customercarlos from rio rancho NM

The water drain pump started to make grinding noises and poor draining

the repairs couldn't be easier, the pump came right out. just loosen the two water drain hoses and out it came. the intallation was just as easy...

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerDenton from Indianapolis IN

Dryer working but drum light not working, bulb ok.

Problem: Drum light not working, bulb ok. Removed 6 screws on panel behind timer, light, buzzer, switches. Lifted back of dryer top then moved dryer top forward and off of dryer. The switch was located above the door. Unhooked wiring plug and took out 2 screws holding in the switch. Installed new switch and repaced bulb. Reassembled as needed and tested light by opening door. Works great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerRandall from Hoffman Estates IL

Load banging noise when drun turns

removed front cover 2 lower screws. once front cover was off, the front drum support bracket was visable. removed 4 screws that hold that in. the drum is now loose and not supported in the front. pulled drive belt tensioner back to release belt. removed 2 top cover screws to get more vertical room to lift drum out. once drum was out, i used a snap ring plyers to take retainer ring off to remove damaged rear drum support rollers. replaced both rear rollers. also replaced drive belt and door lamp. the bearing in the left roller had seized and torn a big hole thru the roller . assembled in reverse order. now drum is nice and quiet

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerSteve from Windsor Locks CT

Noisy drum opreation

Opening the cabinet allowed for a through examination and listing of the worn components: 1 defective idler and mounting shaft, 1 worn drive belt, 2 sagging felt seals, 1 worn glide surface, 1 dead light bulb. Replacement parts arrived in two days. After a through vacuuming, reassembly was a snap. Both roller/shafts and glide pads were replaced as matched pairs. Unit operates now as factory new. I am not a trained repair person but simple logic, sufficient care, and attention to a clean assembly routine is all it took.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 7 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerfanny from madison WI

Burnt out bulb and broken switch

Both my husband and I are not good at DIY or fixing things. I watched the instruction video that was posted on the PartSelect web site. It seems easy to do it, however still very skeptical. My husband decided that there is nothing to lose in trying, so we ordered the parts. It is as easy and simple as the video instruction. We are very happy customers.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsPliers, Screw drivers, Socket set, Wrench set

Customerjames from herington KS

Noisy when running, squeeked at times, belt finally came off

First let me say I went on your forum and got instructions where to download a service manual which helped greatly. Unplugged from outlet. Removed 4 screws holding on the front panel then 4 more holding on the front tumbler support and air duct. Removed wires from light and dryness sensor and clips holding wires to panels. Pulled out the tumbler and removed belt. Removed the two drum support rollers and shafts by removing a nut on the back side of each shaft. Removed snap ring off each old shaft, installed new rollers and fiber washers onto new shafts installed snap ring and replaced on brackets with the old nut. Removed tension spring off idler pulley bracket and one screw holding on the bracket. Installed new pulley and fiber washers on new bracket and reinstalled bracket and spring. Placed new belt on tumber and reinstalled tumbler. Used drill and bit to drill out pop rivits holding on the two front glides that are attached on the front tumbler support and installed new glides and pop rivited in. Reinstalled
front support and air duct checking that felt tumbler seal front and rear were in place. Placed new belt on motor pulley and idler pulley. Reinstalled front panel. Removed bulb cover held on by one screw, Installed new light bulb. Also took shop vac and cleaned inside of cabinet when I had the tumber out. Plugged back in and started, sounds and works like new. Ordered parts on Sunday received Tuesday evening Fed Ex. First time dryer repair. Very happy with PartSelect web site and service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerMatt from Cuyahoga falls OH

Dryer noisy and squeaking belt

Removed two screws from lint trap and pried front of top up gently. Top hinges backwards which is convienent. Two more screws take the front off. Removed drum and old parts. Removed rollers etc. Per the instructions. Cleaned inside of unit with a shop vac.

Reassemble unit and test. Nice and quiet again and working well. Great service fro. Partselect.com.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerIvan from Miami FL

Dryer was not heating and light bulb was broken

Without being a handy man, I saved money by replacing the heating element of our dryer at home. When drying clothing it was not heating, went to partselect and found the proper replacement. It was reeally easy to replace.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerMike from La Vergne TN

Door switch had broken off and interior bulb not working

I first checked the owner's manual an on line documentation from the manufacturer on how to change the door switch on the dryer but found nothing. First step: Turn off breaker to dryer. I then popped the lid of the dryer and could see that the switch was accessible from the top. I was pleasantly surprised to see the parts arrive within 2 days with the lowest cost standard shipment. I loosened the 2 screws holding the switch, unplugged the modular clip, replaced switch, resecured with screws and dropped dryer lid back in place. Interior bulb was busted up, I removed cover plate, base and broken glass, seated replacement bulb, reattached cover and turned breaker back on. Dryer switch and bulb are working again. You sent me exactly what I needed and fast. Thanks for the quick turn around!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-12 of 12