2019482-1-S-Whirlpool-22001274-Water Inlet Valve
2019482-1-S-Whirlpool-22001274-Water Inlet Valve 2019482-2-S-Whirlpool-22001274-Water Inlet Valve 2019482-3-S-Whirlpool-22001274-Water Inlet Valve http://www.partselect.com/Schematics/Maytag/50460.gif

Water Inlet Valve

PartSelect Number PS2019482

This washing machine water inlet valve has two ports for water to enter. This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not stop filling with water.
  • Leaking.
  • No hot or cold water.
  • Will not fill with water.
  • Compare At

    $75.70
  • You Save

    $12.62
  • Your Price

    $63.08
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 20 reviews What's this?
1-5 of 20
 

37 of 42 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: David from Bedford, OH

Only cold water would go through the valve

The washing machine would only fill with cold water. This could be a problem with the controls, the wiring or the valve where the external hoses connect. Various tests, which only those with the proper skills & equipment should perform, revealed that the water valve hot side was not opening. UNPLUG the washing machine before doing any work and especially before opening any access panels. NOTE: Label all fasteners & other connections you remove so you know where they should go back. WITH the Washing Machine UNPLUGGED from the wall outlet, I unscrewed the external hot & cold hoses (make sure the water is turned off first!). I unscrewed the panel that holds the valve in a recess in the back of the machine. On this machine, the panel pulls out of the back with the valve attached to it. So I pulled the panel/valve assembly out of the recess and disconnected its electrical connectors (double-check the washing machine is unplugged before doing this). I also disconnected the internal hose that leads from the valve. Finally, I detached the valve from the panel. Installation is the reverse of removal, although it is a good idea to use a new spring clip or hose clamp, whichever you have, to attach the internal hose to your new valve. Once the valve assembly is properly installed, connect your external hoses, double-checking for hot & cold sides carefully, turn the water on and check for leaks. When all that is ok, plug the washer in and test it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

18 of 19 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Robert from Saratoga, CA

Water was slowly dripping into the wash tub

After first unplugging the washer and shutting off the water to the washer I slid the washer away from the wall. It was a tight cramped space and difficult to get behind it. Most of the time replacing the water inlet valve was spent getting into and out of the work area to get tools and cleaning up a few years of dirt under the washer and water leaking from the hoses after they were removed. The valve removal and re-installation of the new one was pretty straightforward.Just a 3 screws 2 electrical connectors and three hoses. The water inlet hoses were frozen on the old valve and required a wrench to free. I also needed to replace the hose washers which fortunately I had as spares for my garden hoses. I replaced the solenoid leads directly from the old to new valve so as not to get that wrong. Removing the outlet hose clamp was tricky- I needed a fat wrench to depress all the tines and slip it off. Fortunately I was able to reuse it. After securing the mounting screws and tightening the inlet hoses with a wrench just until I met some resistance, I turned the power and water back on and prayed there were no leaks. None- back in business.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 18 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Fredrick from Clinton Corners, NY

Washer would not fill with water

The trouble-shooting section on this website described the above problem and suggested that the proper course of action was to replace the water inlet valve, which I ordered and replaced. Replacement of this part was quick and easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 13 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Brett from Decatur, TX

Water would not shut off and continued to fill washer.

Turned off water supply and disconnected hoses. Removed rear cover where water valve was located. Marked and unplugged wires to valve along with interior hose connected to valve. Unscrewed two screws holding valve to rear cover. Installed new valve with all the above procedures in reverse. Very easy repair that saved us slot of money in service call fees!

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 11 people found this instruction helpful

Parts Used:
  • Water Inlet Valve
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: Donnie from Spring, TX

The water to the washing machine continued to run into the unit when it was supposed cut off. It continue to fill overflowing the tub of the washing machine and onto the floor. The water had to be cut off at the wall in order to stop the inflow of water.

I disconnected both water hoses from the back of the machine. I then unscrewed the panel that holds the water inlet valve. After disconnecting the two electrical connections from the valve and replacing it with the new unit, the job was done.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 20